LSM2-T/6-W3-C Murata Power Solutions Inc, LSM2-T/6-W3-C Datasheet - Page 7
![CONV DC/DC 19.8W 6A 5V SMD](/photos/8/70/87072/lsm2-series_sml.jpg)
LSM2-T/6-W3-C
Manufacturer Part Number
LSM2-T/6-W3-C
Description
CONV DC/DC 19.8W 6A 5V SMD
Manufacturer
Murata Power Solutions Inc
Series
LSM2r
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.LSM2-T6-W3N-C.pdf
(17 pages)
Specifications of LSM2-T/6-W3-C
Output
0.75 ~ 3.3V
Number Of Outputs
1
Power (watts)
19W
Mounting Type
Surface Mount
Voltage - Input
2.4 ~ 5.5V
Package / Case
8-DIP SMD Module
1st Output
0.75 ~ 3.3 VDC @ 6A
Size / Dimension
1.30" L x 0.53" W x 0.34" H (33mm x 13.5mm x 8.6mm)
Power (watts) - Rated
19.8W
Operating Temperature
-40°C ~ 85°C
Efficiency
95.5%
Approvals
CSA, cUL, EN, UL
Dc / Dc Converter O/p Type
Variable
No. Of Outputs
1
Input Voltage
2.4V To 5.5V
Power Rating
19.8W
Output Voltage
3.3V
Output Current
6A
Approval Bodies
UL, CSA
Supply Voltage
5V
Product
Non-Isolated / POL
Output Power
20 W
Input Voltage Range
2.4 V to 5.5 V
Output Voltage (channel 1)
0.75 V to 3.3 V
Output Current (channel 1)
6 A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-1781-2
Start Up Considerations
When power is fi rst applied to the DC/DC converter, operation is different than
when the converter is running and stabilized. There is some risk of start up
diffi culties if you do not observe several application features. Lower output
voltage converters may have more problems here since they tend to have
higher output currents. Operation is most critical with any combination of the
following external factors:
start up surge current may instantaneously reduce the voltage at the input
terminals to below the specifi ed minimum voltage. Even if this voltage depres-
sion is very brief, this may interfere with the on-board controller and possibly
cause a failed start. Or the converter may start but the input current load will
now drive the input voltage below its running low limit and the converter will
shut down.
the voltage may appear to be adequate. Limited external capacitance and/or
too high a source impedance may cause a short downward spike at power up,
causing an instantaneous voltage drop. Use an oscilloscope not a DVM to observe
this spike. The converter’s soft-start controller is sensitive to input voltage. What
matters here is the actual voltage at the input terminals at all times.
tion or brief start up then overcurrent shutdown. Since the input voltage is never
absolutely constant, the converter may start up at some times and not at others.
Solutions
To improve start up, review the conditions above. One of the better solutions is
to place a moderate size capacitor very close to the input terminals. You may
need two parallel capacitors. A larger electrolytic or tantalum cap supplies the
surge current and a smaller parallel low-ESR ceramic cap gives low AC imped-
ance. Too large an electrolytic capacitor may have higher internal impedance
(ESR) and/or lower the start up slew rate enough to upset the DC/DC’s control-
ler. Make sure the capacitors can tolerate refl ected switching current pulses
from the converter.
converter which starts successfully at 3.3 Volts will turn off if the input voltage
decays to below the input voltage theshold, regardless of external capacitance.
1 – Low initial input line voltage and/or poor regulation of the input source.
2 – Full output load current on lower output voltage converters.
3 – Slow slew rate of input voltage.
4 – Longer distance to input voltage source and/or higher external input
5 – Limited or insuffi cient ground plane. External wiring that is too small.
6 – Too small external input capacitance. Too high ESR.
7 – High output capacitance causing a start up charge overcurrent surge.
8 – Output loads with excessive inductive reactance or constant current
If the input voltage is already at the low limit before power is applied, the
If you measure the input voltage before start up with a Digital Voltmeter (DVM),
Symptoms of start-up diffi culties may include failed started, output oscilla-
The capacitors will not help if the input source has poor regulation. A
source impedance.
characteristics.
www.murata-ps.com
spike. Also, make sure that the input voltage ramps up in a reasonably short
time (less than a few milliseconds). If possible, move the input source closer to
the converter to reduce ohmic losses in the input wiring. Remember that the
input current is carried both by the wiring and the ground plane return. Make
sure the ground plane uses adequate thickness copper. Run additional bus wire
if necessary.
more) to reduce output noise at the load and to avoid marginal threshold noise
problems with external logic. An output cap will also “decouple” inductive re-
actance in the load. Certain kinds of electronic loads include “constant current”
characteristics which destabilize the output with insuffi cient capacitance. If the
wiring to the eventual load is long, consider placing this decoupling cap at the
load. Use the Remote Sense input to avoid ohmic voltage drop errors.
the Remote On/Off control fi rst in the off setting (for those converters with an
On/Off Control). After the specifi ed start-up delay (usually under 20 mSec), turn
on the converter. The controller will have already been stabilized. The short
delay will not be noticed in most applications. Be aware of applications which
need “power management” (phased start up).
ity. How low is the resistance of your ground plane? What is the inductance (and
distributed capacitance) of external wiring? Even a detailed mathematical model
may not get all aspects of your circuit. Therefore it is diffi cult to give cap values
which serve all applications. Some experimentation may be required.
Pre-Biased Startup
Newer systems with multiple power voltages have an additional problem
besides startup sequencing. Some sections have power already partially ap-
plied (possibly because of earlier power sequencing) or have leakage power
present so that the DC/DC converter must power up into an existing voltage.
This power may either be stored in an external bypass capacitor or supplied by
an active source.
mable logic or because of blocking diode leakage or small currents passed
through forward biased ESD diodes. Conventional DC/DCs may fail to start up
correctly if there is output voltage already present. And some external circuits
are adversely affected when the low side MOSFET in a synchronous rectifi er
converter sinks current at start up.
tion problems. Essentially, the converter acts as a simple buck converter until the
output reaches its set point voltage at which time it converts to a synchronous
rectifi er design. This feature is variously called “monotonic” because the voltage
does not decay (from low side MOSFET shorting) or produce a negative transient
once the input power is applied and the startup sequence begins.
Increase the input start up voltage if possible to raise the downward voltage
Any added output capacitor should use just enough capacitance (and no
An elegant solution to start up problems is to apply the input voltage with
Finally, it is challenging to model some application circuits with absolute fi del-
This “pre-biased” condition can also occur with some types of program-
The LSM2 series includes a pre-bias startup mode to prevent these initializa-
Selectable-Output POL DC/DC Converters
25 Jun 2010
Single Output, Non-Isolated
MDC_LSM2
LSM2 Series
email: sales@murata-ps.com
Series.B09Δ
Page 7 of 17