LTM4606IV#PBF Linear Technology, LTM4606IV#PBF Datasheet - Page 10

• Manufacturer Part Number: LTM4606IV#PBF
• Description: IC DC/DC UMODULE 6A 133-LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4606IV#PBF

• Design Resources: LTM4606 Spice Model
• Output: 0.6 ~ 5 V
• Number Of Outputs: 1
• Power (watts): 30W
• Mounting Type: Surface Mount
• Voltage - Input: 4.5 ~ 28 V
• Package / Case: 133-LGA
• 1st Output: 0.6 ~ 5 VDC @ 6A
• Size / Dimension: 0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
• Power (watts) - Rated: 30W
• Operating Temperature: -40°C ~ 125°C
• Efficiency: 93%
• Dc To Dc Converter Type: Non-Inverting/Inverting/Step Up/Step Down
• Pin Count: 133
• Input Voltage: 28V
• Output Voltage: 0.6 to 5V
• Switching Freq: 900KHz
• Output Current: 6A
• Package Type: LGA
• Isolation Voltage: Not RequiredV
• Output Type: Adjustable
• Switching Regulator: Yes
• Load Regulation: 0.3%
• Line Regulation: 0.3%
• Mounting: Surface Mount
• Input Voltage (min): 4.5V
• Operating Temperature Classification: Automotive
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Compliant

operaTion
LTM4606
Power Module Description
The LTM4606 is a standalone non-isolated switching mode
DC/DC power supply. It can deliver up to 6A of DC output
current with some external input and output capacitors.
This module provides precisely regulated output voltage
programmable via one external resistor from 0.6V
5.0V
application schematic is shown in Figure 20.
The LTM4606 has an integrated constant on-time current
mode regulator, ultralow R
ing speed and integrated Schottky diodes. With current
mode control and internal feedback loop compensation,
the LTM4606 module has sufficient stability margins and
good transient performance under a wide range of operat-
ing conditions and with a wide range of output capacitors,
even all ceramic output capacitors.
Current mode control provides cycle-by-cycle fast current
limiting. Besides, foldback current limiting is provided in
an overcurrent condition while V
voltage and undervoltage comparators pull the open-drain
PGOOD output low if the output feedback voltage exits a
±10% window around the regulation point. Furthermore,
in an overvoltage condition, internal top FET M1 is turned
off and bottom FET M2 is turned on and held on until the
overvoltage condition clears.
10
DC
over a 4.5V to 28V input voltage range. The typical
DS(ON)
FB
FETs with fast switch-
drops. Internal over-
DC
to
Input filter and noise cancellation circuits reduce the noise
coupling to I/O sides, and ensure the electromagnetic
interference (EMI) to meet EN55022 Class B limits.
Pulling the RUN pin below 1V forces the controller into its
shutdown state, turning off both M1 and M2. At low load
currents, discontinuous mode (DCM) operation can be
enabled to achieve higher efficiency compared to continu-
ous mode (CCM) by setting the FCB pin higher than 0.6V.
When the DRV
5V linear regulator powers the internal gate drivers. If a
5V external bias supply is applied on the DRV
an efficiency improvement will occur due to the reduced
power loss in the internal linear regulator. This is especially
true at the higher input voltage range.
The MPGM, MARG0 and MARG1 pins are used to sup-
port voltage margining, where the percentage of margin
is programmed by the MPGM pin, and the MARG0 and
MARG1 selected margining. The PLLIN pin provides fre-
quency synchronization of the device to an external clock.
The TRACK/SS pin is used for power supply tracking and
soft-start programming.
CC
pin is connected to INTV
CC
an integrated
CC
pin, then
4606fb