APXW005A0X3-SRZ Lineage Power, APXW005A0X3-SRZ Datasheet - Page 20

• Manufacturer Part Number: APXW005A0X3-SRZ
• Description: PWR MOD DC/DC NON-ISOL 9-36V 5A
• Manufacturer: Lineage Power
• Series: ProLynx™r
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of APXW005A0X3-SRZ

• Output: 3 ~ 18V
• Number Of Outputs: 1
• Power (watts): 90W
• Mounting Type: Surface Mount
• Voltage - Input: 9 ~ 36V
• Package / Case: 7-SMD Module
• 1st Output: 3 ~ 18 VDC @ 5A
• Size / Dimension: 0.80" L x 0.45" W x 0.34" H (20.3mm x 11.4mm x 8.5mm)
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 95.9%
• Approvals: CSA, EN, UL, VDE
• Input Voltage Range: 9 V to 36 V
• Output Voltage (channel 1): 3 VDC to 18 VDC
• Output Current (channel 1): 2.5 A to 5 A
• Package / Case Size: 20.3 mm x 11.4 mm x 8.5 mm
• Output Type: Non-Isolated
• Output Voltage: 3 VDC to 18 VDC
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 555-1172-2; CC109151916

Preliminary Data Sheet
October 28, 2010
Surface Mount Information
Pick and Place
The 9-36V ProLynx
construction and are designed for a fully automated
assembly process. The modules are fitted with a label
designed to provide a large surface area for pick and
place operations. The label meets all the requirements
for surface mount processing, as well as safety
standards, and is able to withstand reflow
temperatures of up to 300
product information such as product code, serial
number and the location of manufacture.
Nozzle Recommendations
The module weight has been kept to a minimum by
using open frame construction. Variables such as
nozzle size, tip style, vacuum pressure and placement
speed should be considered to optimize this process.
The minimum recommended inside nozzle diameter
for reliable operation is 3mm. The maximum nozzle
outer diameter, which will safely fit within the allowable
component spacing, is 7 mm.
Lead Free Soldering
The 9-36V ProLynx
and RoHS compliant and fully compatible in a Pb-free
soldering process. Failure to observe the instructions
below may result in the failure of or cause damage to
the modules and can adversely affect long-term
reliability.
Pb-free Reflow Profile
Power Systems will comply with J-STD-020 Rev. C
(Moisture/Reflow Sensitivity Classification for
Nonhermetic Solid State Surface Mount Devices) for
both Pb-free solder profiles and MSL classification
procedures. This standard provides a recommended
forced-air-convection reflow profile based on the
volume and thickness of the package (table 4-2). The
suggested Pb-free solder paste is Sn/Ag/Cu (SAC).
The recommended linear reflow profile using Sn/Ag/Cu
solder is shown in Fig. 41. Soldering outside of the
recommended profile requires testing to verify results
and performance.
MSL Rating
The 9-36V ProLynx
Storage and Handling
The recommended storage environment and handling
procedures for moisture-sensitive surface mount
packages is detailed in J-STD-033 Rev. A (Handling,
Packing, Shipping and Use of Moisture/Reflow
Sensitive Surface Mount Devices). Moisture barrier
bags (MBB) with desiccant are required for MSL
ratings of 2 or greater. These sealed packages should
not be broken until time of use. Once the original
LINEAGE
POWER
TM
TM
TM
modules use an open frame
modules are lead-free (Pb-free)
modules have a MSL rating of 2.
o
C. The label also carries
9 – 36Vdc input; 3Vdc to 18Vdc output; 5A to 2.5A output current
9-36V ProLynx
TM
package is broken, the floor life of the product at
conditions of ≤ 30°C and 60% relative humidity varies
according to the MSL rating (see J-STD-033A). The
shelf life for dry packed SMT packages will be a
minimum of 12 months from the bag seal date, when
stored at the following conditions: < 40° C, < 90%
relative humidity.
Figure 41. Recommended linear reflow profile
using Sn/Ag/Cu solder.
Post Solder Cleaning and Drying
Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect
both the reliability of a power module and the testability
of the finished circuit-board assembly. For guidance on
appropriate soldering, cleaning and drying procedures,
refer to Board Mounted Power Modules: Soldering and
Cleaning Application Note (AN04-001).
5A: Non-isolated DC-DC Power Modules
300
250
200
150
100
50
0
Per J-STD-020 Rev. C
Heating Zone
1°C/Second
Peak Temp 260°C
Reflow Time (Seconds)
* Min. Time Above 235°C
*Time Above 217°C
15 Seconds
60 Seconds
Cooling
Zone
20