AXH003A0X4 Lineage Power, AXH003A0X4 Datasheet - Page 12
![CONVER DC/DC 0.75 3.63V @ 3A SIP](/photos/8/70/87049/mfg_axa003a0x_series_sml.jpg)
AXH003A0X4
Manufacturer Part Number
AXH003A0X4
Description
CONVER DC/DC 0.75 3.63V @ 3A SIP
Manufacturer
Lineage Power
Series
Austin MiniLynx™r
Type
Point of Load (POL) Non-Isolated with Remote On/Offr
Datasheet
1.AXH003A0XZ.pdf
(18 pages)
Specifications of AXH003A0X4
Rohs Status
RoHS non-compliant
Output
0.75 ~ 3.63V
Number Of Outputs
1
Power (watts)
10W
Mounting Type
Through Hole
Voltage - Input
2.4 ~ 5.5V
Package / Case
5-SIP Module
1st Output
0.75 ~ 3.63 VDC @ 3A
Size / Dimension
0.90" L x 0.26" W x 0.40" H (22.9mm x 6.6mm x 10.2mm)
Power (watts) - Rated
10W
Operating Temperature
-40°C ~ 85°C
Efficiency
94%
Approvals
CSA, EN, UL, VDE
3rd Output
-
2nd Output
-
Other names
555-1007
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AXH003A0X4-SR
Manufacturer:
TYCO
Quantity:
20 000
Data Sheet
October 2, 2009
Feature Description
Remote On/Off
The Austin MiniLynx
On/Off pin for remote On/Off operation. Two On/Off
logic options are available in the Austin MiniLynx
series modules. Positive Logic On/Off signal, device
code suffix “4”, turns the module ON during a logic High
on the On/Off pin and turns the module OFF during a
logic Low. Negative logic On/Off signal, no device code
suffix, turns the module OFF during logic High on the
On/Off pin and turns the module ON during logic Low.
For positive logic modules, the circuit configuration for
using the On/Off pin is shown in Figure 30. The On/Off
pin is an open collector/drain logic input signal (Von/Off)
that is referenced to ground. During a logic-high
(On/Off pin is pulled high internal to the module) when
the transistor Q1 is in the Off state, the power module is
ON. Maximum allowable leakage current of the
transistor when Von/off = V
logic-low when the transistor Q1 is turned-On, the
power module is OFF. During this state VOn/Off must
be less than 0.3V. When not using positive logic On/off
pin, leave the pin unconnected or tie to V
Figure 30. Circuit configuration for using positive
logic On/OFF.
For negative logic On/Off devices, the circuit
configuration is shown is Figure 31. The On/Off pin is
pulled high with an external pull-up resistor (typical R
up
logic High is applied to the On/Off pin and the power
module is Off. The minimum On/off voltage for logic
High on the On/Off pin is 1.5Vdc. To turn the module
ON, logic Low is applied to the On/Off pin by turning ON
Q1. When not using the negative logic On/Off, leave
the pin unconnected or tie to GND.
LINEAGE
= 5k, +/- 5%). When transistor Q1 is in the Off state,
I
ON/OFF
GND
VIN+
POWER
ON/OFF
V
Q1
ON/OFF
+
_
TM
SIP power modules feature an
R1
IN,max
R2
R3
R4
is 10µA. Applying a
2.4 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 3A output current
Q2
MODULE
PWM Enable
IN.
Q3
TM
CSS
Austin MiniLynx
pull-
Figure 31. Circuit configuration for using negative
logic On/OFF.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally
once the output current is brought back into its specified
range. The typical average output current during hiccup
is 3.5A.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, module operation is disabled. The module will
begin to operate at an input voltage above the
undervoltage lockout turn-on threshold.
Overtemperature Protection
To provide over temperature protection in a fault
condition, the unit relies upon the thermal protection
feature of the controller IC. The unit will shutdown if
the thermal reference point T
(typical), but the thermal shutdown is not intended as
a guarantee that the unit will survive temperatures
beyond its rating. The module will automatically
restart after it cools down.
ON/OFF
VIN+
GND
TM
V
Q1
SIP Non-isolated Power Modules:
R
I
ON/OFF
pull-up
ON/OFF
+
_
ref
R1
R2
, exceeds 140
MODULE
PWM Enable
Q2
o
C
CSS
12