45111 Parallax Inc, 45111 Datasheet - Page 103
45111
Manufacturer Part Number
45111
Description
MANUAL FOR SX-KEY/BLITZ VER. 2.0
Manufacturer
Parallax Inc
Datasheet
1.45111.pdf
(184 pages)
Specifications of 45111
Accessory Type
Manual
Product
Microcontroller Accessories
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With/related Products
Parallax microcontroller
For Use With
70002PAR - GUIDE PROG THE SX MICRO -DAUBACH
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
- Current page: 103 of 184
- Download datasheet (2Mb)
The following are points to remember with Wake-Up Interrupts:
An RTCC rollover interrupt event will not occur during SLEEP mode and thus can not wake up the SX
chip from a SLEEP mode.
10.5 Creating Tables
10.5.1 Data Tables
Tables of 8-bit or 12-bit data may be stored in the unused program space of the SX chip. Tables of data
may be necessary in cases where a set of data can not be calculated by an equation, or will take too long
to calculate. There are two methods available to store data tables in the SX chip.
If only 8-bit data is required, the RETW method may be used to create the data table. This method uses
a set of RETW commands which each hold an 8-bit data value as their operand. The table is preceded by
a JMP PC+W command. By moving an index value to W and then CALLing the first line of the table,
which is the JMP command, W is added to the program counter and upon the next clock cycle, the
proper RETW command is executed. RETW simply moves its operand to W and then returns to the line
after the CALL.
To create an 8-bit data table with the RETW command:
1) Set the table’s location, and insert a label and a JMP PC+W command at the start of the table.
2) Add as many RETW commands as necessary.
3) When data is needed from the table, move the index value of the desired item to W and CALL the
The interrupt routine must be located starting at address $0 in the SX program.
The interrupt routine should take a maximum of 6 cycles less than the desired cycle time slot. (i.e. if
the interrupt should execute once every 20 cycles, it needs to be less than 15 cycles in size).
The SX chip will activate the interrupt routine exactly 3 clock cycles (Turbo) or 8 clock cycles
(Compatible) after an RTCC rollover event occurs. This deterministic feature allows for jitter-free
interrupt response.
table. Upon returning, the 8-bit value is in W.
10 SX Special Features and Coding Tips
SX-Key/Blitz Development System Manual 2.0 Parallax, Inc. Page 103
Related parts for 45111
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Terminals 3 Pin Single Row Header (long)
Manufacturer:
Parallax Inc
Part Number:
Description:
Headers & Wire Housings 16 Pin Single Row Header
Manufacturer:
Parallax Inc
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
Part Number:
Description:
BOOK UNDERSTANDING SIGNALS
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
COMPETITION RING FOR SUMOBOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
TEXT INFRARED REMOTE FOR BOE-BOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
Part Number:
Description:
BOOK UNDERSTANDING SIGNALS
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
BOARD EXPERIMENT+LCD NX-1000
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
IC MCU 2K FLASH 50MHZ SO-18
Manufacturer:
Parallax Inc
Datasheet: