DM-COP8/28D National Semiconductor, DM-COP8/28D Datasheet - Page 187
DM-COP8/28D
Manufacturer Part Number
DM-COP8/28D
Description
CABLE FOR DEBUG MODULE 28-DIP
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of DM-COP8/28D
Accessory Type
28-DIP Target Cable
For Use With/related Products
MetaLink Debug Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*DM-COP8/28D
- Current page: 187 of 254
- Download datasheet (2Mb)
Installing the EPU Software
You must have at least 1700 kilobytes of free disk space on your PC to install the EPU
host software. To install this software type the following from the DOS command line:
The install function will prompt for paths.
Installing the Assembler Software
Place the COP8-DEV-IBMA disk into a floppy drive. Enter:
Install will prompt for the drives letter of the source drive. Enter if other than a:. It will
then prompt for the directory to install the files. If other than c:\cop enter the correct
path. After confirming there is room for the files, INSTALL copies them to the
installation directory.
Pay particular attention to the notes on editing your CONFIG.SYS and AUTOEXEC.BAT
files. You must properl.y set up your PATH and environment variables. If you need to
redisplay the notes, enter TYPE ASMREAD.ME
Installing the Hardware
Attach the serial cable provided to either COM1 or COM2 of the PC and connect the other
end to the EPU. Plug in the AC adapter provided into the AC outlet. Connect the output
of the adapter to the DC jack provided on the EPU. In order to observe the I/Os the target
cable may be plugged into the header on the EPU. CAUTION: Failure to remove the
conductive foam from the target cable may result in improper operation of the unit.
Assembling and Running a Program on the EPU
Assume that the EPU and Assembler software have been installed in path: c:\epu-cop8\.
Then use the following to assemble a program.
To assemble a program. The various flags are explained in the COP8 Assembler/Linker/
Librarian Users Manual.
To link the program
To load it into the EPU
C:\>a:\install a: c: \epu-cop8
C:\>x:\install
C:\>x:\install
C:\EPU-COP8>asmcop /1 /sy sample /PW=132
C:\EPU-COP8>lncop sample /fo=h
C:\EPU-COP8>epu888gg sample
or
(Where x is either A or B)
(Where x is either A or B)
DEVELOPMENT SUPPORT
3-7
Related parts for DM-COP8/28D
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CABLE FOR DEBUG MODULE 20-DIP
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
CABLE FOR DEBUG MODULE 44-PLCC
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 10A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH PWR ROCKER DPST SNAP-IN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER SPST ILUM 10A/125V
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT W/MRK QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER ILLUM 10A GRN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
MINI ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER SPST 3A QC
Manufacturer:
C&K Components
Datasheet: