ATAB6817 Atmel, ATAB6817 Datasheet - Page 6

• Manufacturer Part Number: ATAB6817
• Description: BOARD EVAL FOR T6817
• Manufacturer: Atmel

Specifications of ATAB6817

• Main Purpose: Power Management, Half H-Bridge Driver (Internal FET)
• Embedded: No
• Utilized Ic / Part: T6817
• Primary Attributes: 3 Channel High & Low Side Internal Switch
• Secondary Attributes: Graphical User Interface
• Processor To Be Evaluated: T6817
• Processor Series: T6817
• Interface Type: SPI
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: - 0.3 V to + 40 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.2
3.3
3.4
3.5
3.6
6
Power-supply Fail
Open-load Detection
Overtemperature Protection
Short-circuit Protection
Inhibit
T6817
In case of over- or undervoltage at pin VS, an internal timer is started. When the undervoltage
delay time (t
the output register is set and all outputs are disabled. When normal voltage is present again, the
outputs are enabled immediately. The PSF bit remains high until it is reset by the SRR bit in the
input register.
If the open-load detection bit (OLD) is set to low, a pull-up current for each high-side switch and
a pull-down current for each low-side switch is turned on (open-load detection current I
I
tion), the corresponding bit of the output in the output register is set to high. Switching on an
output stage with the OLD bit set to low disables the open-load function for this output. If bit SI is
set to low, the open-load function is also switched off.
If the junction temperature exceeds the thermal prewarning threshold, T
prewarning bit (TP) in the output register is set. When the temperature falls below the thermal
prewarning threshold, T
complete 16-bit data word: with CS = high to low, the state of TP appears at pin DO. After the
microcontroller has read this information, CS is set high and the data transfer is interrupted with-
out affecting the state of the input and output registers.
If the junction temperature exceeds the thermal shutdown threshold, T
disabled and all bits in the output register are set high. The outputs can be enabled again when
the temperature falls below the thermal shutdown threshold, T
been written to the SRR bit in the input register. Thermal prewarning and shutdown threshold
have hysteresis.
The output currents are limited by a current regulator. Current limitation takes place when the
overcurrent limitation and shutdown threshold (I
internal timer is started. The shorted output is disabled when during a permanent short the delay
time (t
cuit detection bit (SCD) is set. If the temperature prewarning bit TP in the output register is set
during a short, the shorted output is disabled immediately and SCD bit is set. By writing a high to
the SRR bit in the input register, the SCD bit is reset and the disabled outputs are enabled.
There are two ways to inhibit the T6817:
In both cases, all output stages are turned off but the serial interface stays active. The output
stages can be activated again by bit SI = 1 and by pin 5 (INH) switched back to 5V.
LS1-3
1. Set bit SI in the input register to zero
2. Switch pin 5 (INH) to 0V
). If V
dSd
) programmed by the short-circuit timer bit (SCT) is reached. Additionally, the short-cir-
VS
dUV
-V
HS1-3
, t
dOV
or V
) programmed by the SCT bit is reached, the power supply fail bit (PSF) in
jPW reset
LS1-3
is lower than the open-load detection threshold (open-load condi-
, the bit TP is reset. The TP bit can be read without transferring a
HS1-3
, I
LS1-3
) are reached. Simultaneously, an
j switch on
j switch off
, and when a high has
jPW set
, the temperature
, the outputs are
4670E–BCD–04/09
HS1-3
,