MAX11068EVKIT+ Maxim Integrated Products, MAX11068EVKIT+ Datasheet - Page 30

• Manufacturer Part Number: MAX11068EVKIT+
• Description: KIT SMART BATT MEASUREMENT 12CH
• Manufacturer: Maxim Integrated Products

Specifications of MAX11068EVKIT+

• Main Purpose: Power Management, Battery Monitor, Car
• Utilized Ic / Part: MAX11068
• Primary Attributes: Monitors Current, Voltage, Temperature
• Secondary Attributes: 1 ~ 12 Cell- Li-Ion, 1 ~ 12 Cell- NiMH
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Embedded: -

MAX11068 Evaluation System
Table_29._Header_J103_Pinout
Table_30._Header_J4_and_J5_(U1_Fanout)
The MAX11068 device is reset when the device’s VAA
regulator drops below the power-on-reset (POR) thresh-
old. A soft reset is accomplished in one of two ways,
depending on the type of SHDNIN_ control the EV kit is
configured for (see the Device Startup section). A hard
reset can also be initiated by cycling the power on the
30_ _ ______________________________________________________________________________________
PIN_NO.
PIN_NO._
(ODD)
10
12
13
14
15
16
17
18
19
20
11
13
15
17
19
11
1
2
3
4
5
6
7
8
9
1
3
5
7
9
ASSOCIATION
SHDNINB
GNDLB
SHDNB
GNDLB
SDALB
SCLLB
SHDNINA
NET_
N.C.
N.C.
N.C.
N.C.
AUXIN2A
ALRMUA
GPIO1 A
GPIO0 A
ALRMLA
GPIO2A
GNDUA
VDDUA
SDAUA
GNDLA
SCLUA
VDDLA
DCINA
SCLLA
SDALA
CP+A
CP-A
N.C.
N.C.
J4_
PIN_NAME
PIN_NO._
(EVEN)
10
12
14
16
18
20
2
4
6
8
ASSOCIATION
AUXIN1A
AGNDA
THRMA
VAAA
C12A
C11A
C10A
REFA
HVA
C9A
C8A
C7A
C6A
C5A
C4A
C3A
C2A
C1A
C0A
N.C.
J5
GNDLB
GNDLB
GNDLB
GNDLB
GNDLB
GNDLB
GNDLB
GNDLB
GNDLB
NET_
—
Reset
Table_31._Header_J6_and_J7_(U2_Fanout)
DCIN input pin. After a reset, all the MAX11068 registers
are restored to their POR values. Refer to the MAX11068
IC data sheet for additional details.
Software_SHDNIN__Control:
1) Check the SHDN checkbox.
2) Uncheck the SHDN checkbox.
Hardware_SHDNIN__Control:
1) Disconnect the SHDNIN_ net from the MINIQUSB’s
2) Reinstall the shunt.
Tables 30–33 provide the complete pinouts for each pair
of the 20-pin single-row headers (J4 and J5, J6 and J7,
J104 and J105, and J106 and J107) provided on the
PIN_NO.
3.3V rail:
• If board (A) is interfaced to the MINIQUSB com-
• If board (B) is interfaced to the MINIQUSB
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
mand module, remove the shunt from its JU12
jumper.
command module, remove the shunt from its
JU112 jumper.
UVSEL0CA
UVSEL1CA
UVSEL2CA
DCINCA
C12CA
C11CA
C10CA
HVCA
C9CA
C8CA
C7CA
C6CA
C5CA
C4CA
C3CA
C2CA
C1CA
C0CA
N.C.
N.C.
J6
20-Pin Header Footprints
PIN_NAME
ALRMOUTCA
ALRMINCA
TOPSELCA
SHDNINCA
OVSEL3CA
OVSEL2CA
OVSEL1CA
OVSEL0CA
GNDUCA
AGNDCA
AGNDCA
AGNDCA
AGNDCA
VDDUCA
CP+CA
VAACA
CP-CA
CDCA
N.C.
N.C.
J7