ATSTK600 Atmel, ATSTK600 Datasheet - Page 16

DEV KIT FOR AVR/AVR32

ATSTK600

Manufacturer Part Number
ATSTK600
Description
DEV KIT FOR AVR/AVR32
Manufacturer
Atmel
Series
AVR®r
Type
MCUr
Datasheets

Specifications of ATSTK600

Processor To Be Evaluated
AVR and AVR32
Data Bus Width
8 bit
Interface Type
RS-232, USB
Silicon Manufacturer
Atmel
Core Architecture
AVR
Core Sub-architecture
AVR UC3
Silicon Core Number
STK600
Silicon Family Name
AVR
Kit Contents
Board
Rohs Compliant
Yes
For Use With/related Products
Atmel AVR Devices
For Use With
ATSTK600-ATTINY10 - STK600-ATTINY10 SOCKET PACKAGE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Contents
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATSTK600
Manufacturer:
Atmel
Quantity:
135
Part Number:
ATSTK600-ATTINY10
Manufacturer:
Atmel
Quantity:
135
Part Number:
ATSTK600-DIP40
Manufacturer:
Atmel
Quantity:
135
Part Number:
ATSTK600-RC14
Manufacturer:
Atmel
Quantity:
135
Part Number:
ATSTK600-RC15
Manufacturer:
Atmel
Quantity:
135
5.4 CMD_PROGRAM_FLASH_PP
Table 5-9. Command format.
Field
Answer ID
Status
Field
Command ID
Nmb bytes (MSB
Nmb bytes (LSB)
Mode
pollTimeout
Data
Data
Data
Notes:
16
(1)
1. See details in list below.
AVR079
Size
1 byte
1 byte
Size
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
Table 5-8. Valid Result Values for the answer to this command.
This command will program data into the FLASH memory of the target device if it
succeeds. For devices with the FLASH organized in pages, the data address and size
used with this command must confirm to that of the device. I.e. one ProgramFlash
command is used to program one page in the target device.
XML PATH: /AVRPART/ICE_SETTINGS/STK600/PpProgramFlash/
Mode byte description
• Bit 0: This bit indicates whether to use byte ‘0’ or page ‘1’ programming.
• Bit 1-3 are the pagesize bits, pagesize are given in bytes not words, see table
• Bit 4-5 are not in use.
• Bit 6 must be set to ‘1’ when it is the very last page to be programmed, otherwise
• Bit 7 indicates if a page write should be issued (Transfer data to flash). Normally it
Value
STATUS_CMD_OK
STATUS_RDY_BSY_TOUT
below.
‘0’.
should always be set ‘1’. However, if the page size of the target device is too large
to be covered by one Program Flash command (because the amount of available
SRAM in STK600 is limited) this can be used to let 2 or more commands fill the
page buffer of the target device. The transfer data to flash flag should then only be
set on the last command.
Values
CMD_CHIP_ERASE_PP
See table below
Values
CMD_PROGRAM_FLASH_PP
XML: mode, *see description
below
XML: pollTimeout
Data 1
...
Data N
Description
Operation succeeded
No response from target device within specified
timeframe
Description
Answer id
A Result Value indicating the result of the
operation
Description
Command id
Total number of bytes to program (MSB)
Total number of bytes to program (LSB)
Mode byte, *see description below
pollTimeout (in ms)
8133A-AVR-04/08

Related parts for ATSTK600