101-0399 Rabbit Semiconductor, 101-0399 Datasheet - Page 17

• Manufacturer Part Number: 101-0399
• Description: KIT DEV RABBIT RCM2000 INT'L
• Manufacturer: Rabbit Semiconductor
• Series: RabbitCore 2000r
• Type: MPU Moduler

Specifications of 101-0399

• Contents: RabbitCore Module, Dev. Board, AC Adapter, Cable and Dynamic C® CD-Rom
• For Use With/related Products: RCM2000, RCM2010, RCM2020
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 101-399; 101-399

• A message reports “No Rabbit Processor Detected” in cases where the RCM2000 and
• The programming cable must be connected to the RCM2000. (The colored wire on the
• To check if you have the correct serial port, select
3.1.1.1 Single-Stepping
Compile or re-compile
program will compile and the screen will come up with a highlighted character (green) at
the first executable statement of the program. Use the
F8
j< ...
to press
3.1.1.2 Watch Expressions
Type
come up. Type the lower case letter j and click on add to top and close. Now continue sin-
gle-stepping with
printed in the watch window. Note how the value of
executed.
3.1.1.3 Break Point
Move the cursor to the start of the statement:
To set a break point on this statement, type
menu. A red highlight will appear on the first character of the statement. To get the pro-
gram running at full speed, type
advance until it hits the break point. Then the break point will start flashing and show both
red and green colors. Note that LED DS3 is now solidly turned on. This is because we
have passed the statement turning on LED DS3. Note that
value 32000. This is because the loop above terminated when
To remove the break point, type
continue program execution, type
should be flashing again since the program is running at full speed.
User’s Manual
the Prototyping Board are not connected together, the wall transformer is not con-
nected, or is not plugged in. (The red power LED lights whenever power is connected.)
programming cable is closest to pin 1 on header J3 on the RCM2000, as shown in
Figure 2.) The other end of the programming cable must be connected to the PC serial
port. The COM port specified in the Dynamic C
one the programming cable is connected to.
type
different serial port using the Dynamic C
you are plugged into. Don’t change anything in this menu except the COM number.
The baud rate should be 115,200 bps and the stop bits should be 1.
key is pressed, the cursor will advance one statement. When you get to the
<Ctrl-W>
<Ctrl-Y>
F8
statement, it becomes impractical to single-step further because you would have
for(j=0; j<25000; j++);
thousands of times. We will use this statement to illustrate watch expressions.
or chose
. If the “BIOS successfully compiled …” message does not display, try a
F8
. Each time you step, the watch expression (
FLASHLED.C
Add/Del Watch Expression
F9
F2
F9
or select
or select
or select
by clicking the
F2
Options
Run
Toggle Breakpoint
or select
Run
on the
Options
from the
j
Compile
Compile
F8
advances when the statement
menu until you find the serial port
in the
Toggle Breakpoint
Run
key to single-step. Each time the
j
menu must be the same as the
in the watch window has the
Inspect
Run
menu. The program will
j
, then
button on the task bar. The
reached 32000.
j
on the
menu. Now the LED
) will be evaluated and
Compile BIOS
menu. A box will
Run
from the
menu. To
for(j=0,
j++
, or
Run
is
13