SUPERPRO9000U(ROHS) Xeltek, SUPERPRO9000U(ROHS) Datasheet - Page 25

• Manufacturer Part Number: SUPERPRO9000U(ROHS)
• Description: PROGRAMMER GANG QUAD SKT W/USB
• Manufacturer: Xeltek
• Series: SuperPro 9000Ur
• Type: Gang-Universal Programmerr

Specifications of SUPERPRO9000U(ROHS)

• Contents: 4 sets 48-DIP Programming Sockets, Programmer, AC Adapter, USB Cable, Users Guide and Power Supply
• For Use With/related Products: E/EPROM, FLASH, PLD, Micros and more listed on Device Sheet, 38,000+ Devices Supported.
• For Use With: 415-1029 - SOCKET ADAPTER FOR SDIP42415-1028 - SOCKET ADAPTER FOR TQFP32415-1027 - SOCKET ADAPTER FOR TSOP56415-1025 - SOCKET ADAPTER FOR SOIC20415-1024 - SOCKET ADAPTER FOR TSOP40415-1023 - SOCKET ADAPTER FOR SOP44415-1022 - SOCKET ADAPTER FOR TSOP56415-1019 - SOCKET ADAPTER FOR SOIC16/SOIC8415-1018 - SOCKET ADAPTER FOR SOIC28415-1015 - SOCKET ADAPTER FOR PLCC28415-1014 - SOCKET ADAPTER FOR PLCC20415-1013 - SOCKET ADAPTER FOR PLCC32415-1017 - SOCKET ADAPTER FOR PLCC44
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 415-1009; SUPERPRO 9000U; SUPERPRO 9000U(ROHS)

buffer blank as devices changed, the programmer will fill all the HEX/ASCII buffer data with FF or 00 (Hex), and
Fuse buffer data with 1 or 0 after the devices selected. An encrypted chip is displayed as a blank chip. EEPROM
does not need Bank_check.
How to write over a chip into blank?
1) For chips that can be erased electrically, execute Erase
2) For chips that can be erased with ultraviolet ray, use the ultraviolet ray eraser for 3-30 minutes.
3) For OTP, once written it is unable to be written over back to blank again.
Erase:
Erase the chip to blan k state. This operation can only be executed with the chip that can be erased electrically.
EEPROM doesn't need to execute this operation. If you need a chip of blank state you can directly program the blank
data to the chip. Some chips that can be erased electrically are able to become an OTP by configure the ConfigWord.
Please refer to the device data manual.
Protect:
1) Security the data to make them unreadable. Whether the protect state is readable or not, affect the editing of the
Note: Some manufacturers’ chips with window will be used again after full-protect, and ultraviolet ray eraser is also
unable to erase.
2) For FLASH chips, this function is for protecting the data in the chip s. The protected chip is not re -writable
This operation is required to be used with Dev. Config. Users need to identify the Sector to protect. There are two
ways to select the Sector,
Above are commonly used functions. For some devices, which have special requirements and functions, the
operation function window may be different.
For detailed information, user could refer to:
1. The manual of the device
2. Dev. Information
operation function. When the protect state is unreadable, the Protect operation will be added to the operation
function window. As long as the Protect function is executed, the chip will be protected. If the protect state is
readable, the state None and all the protect options w ill be listed out for user to select. The protect operation will
be executed according to the ConfigWord. If user select None, the protect operation is non -functional.
before the protection removed. The Erase operation would remove the protection.
1. Users enter the address of several (max 8) sectors to decide the sectors to protect. After the protect
2. Divide the chip into several sector groups, users can only choose these groups to protect.
Security: equal to Protect,
Erease_All: equal to Erase
Protect_All: equal to Protect
Lock_Bit: the notion for protects. Please refer to the manual.
operation, the sectors whose addresses are entered will be protected.