HS7705KCI02H Renesas Electronics America, HS7705KCI02H Datasheet - Page 236
HS7705KCI02H
Manufacturer Part Number
HS7705KCI02H
Description
ON CHIP DEBUG EMULATOR W/TRACE
Manufacturer
Renesas Electronics America
Specifications of HS7705KCI02H
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 236 of 250
- Download datasheet (2Mb)
6.5.6
1. When [Go to cursor], [Step In], [Step Over], or [Step Out] is selected, the settings of Break
2.
3.
4.
5.
6.
7.
6.5.7
When a completion-type exception occurs during exception branch acquisition, the next address to
the address in which an exception occurs is acquired.
6.5.8
In the [Configuration] dialog box, if [User] is set while the [UBC mode] list box has been set, the
STEP-type commands that use Break Condition2 for implementation cannot be used. If these
commands are used, the message box shown in figure 6.14 is displayed.
210
Condition 2 are disabled.
Break Condition 2 is disabled when an instruction to which a BREAKPOINT has been set is
executed. Accordingly, do not set a BREAKPOINT to an instruction which satisfies Break
Condition 2.
When a Break Condition is satisfied, emulation may stop after two or more instructions have
been executed.
If a PC break address condition is set to the slot instruction after a delayed branch instruction,
user program execution cannot be terminated before the slot instruction execution; execution
stops before the branch destination instruction.
Break Condition 1,2 is used as the measurement range in the performance measurement
function when (P) is added and displayed as Enable(P) on the [Condition] page. This applies
when the Break Condition is displayed with the BREAKCONDITION_DISPLAY command
in the command-line function. In this case, a break does not occur when Break Condition 1,2
is satisfied.
Note that a break occurs with a break satisfaction condition by an instruction that has been
cancelled due to the generation of an exception.
Use the sequential break or count break with the L-bus condition. If such break is used with
the I-bus condition, it will not operate correctly.
Notes on Setting the [Break Condition] Dialog Box and the BREAKCONDITION_
SET Command
Notes on Setting the [Trace] Window
Notes on Setting the UBC_MODE Command
Figure 6.14 [HDI] Message Box
Related parts for HS7705KCI02H
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: