MPC5554EVBGHS Freescale Semiconductor, MPC5554EVBGHS Datasheet - Page 51

• Manufacturer Part Number: MPC5554EVBGHS
• Description: BOARD EVAL GREEN HILLS SOFTWARE
• Manufacturer: Freescale Semiconductor
• Type: Microcontrollerr

Specifications of MPC5554EVBGHS

• Contents: Eval Board and Demo Software
• Processor To Be Evaluated: MPC55xx
• Data Bus Width: 32 bit
• Interface Type: RS-232, Ethernet
• Core Architecture: Power
• For Use With/related Products: MPC5554
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Freescale Semiconductor
Table 5
Table 6
Table 9
Table 14
Table 17
Table 19
Table 20
Table 22
Table 23
Table 24
Table 25
Location
ESD Ratings:
VCR/POR Electrical Specifications:
DC Electrical Specifications:
Flash Program and Erase Specifications (T
Pad AC Specifications (V
Reset and Configuration Pin Timing:
JTAG Pin AC Electrical Characteristics
Bus Operation Timing:
External Interrupt Timing (IRQ Signals)
eTPU Timing
eMIOS Timing
Changed footnote 2 from:
to:
• ‘Device failure is defined as: ‘If after exposure to ESD pulses, the device no longer meets the device specification
• Device failure is defined as: ‘If after exposure to ESD pulses, the device does not meet the device specification
• Added footnote 1 to specs 1, 2, and 3 that reads: The internal POR signals are V
• Reformatted columns.
• Added footnote that reads: V
• Added (T
• Footnote 1, Changed ‘Typical program and erase times assume nominal supply values and operation at 25
• Footnote 1, changed ‘V
• Footnote 1: Removed V
• Footnote 1: Removed V
• External Bus Frequency in the table heading: Added footnote that reads: Speed is the nominal maximum
• Specifications 5, 6, 7, and 8: Reordered the EBI signals within each specification.
• Specifications 7 and 8: Removed EBI signals BDIP, OE, TSIZ[0:1], WE/BE[0:3].
• Footnote 1: Removed V
• Footnote 8: Changed EBTS to SIU_ECCR[EBTS].
• Footnote 1: Removed V
• Footnote 1: Changed V
• Footnote 1: Changed V
requirements. Complete DC parametric and functional testing will be performed per applicable device
specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.’
requirements, which includes the complete DC parametric and functional testing at room temperature and hot
temperature.
On power up, assert RESET before the internal POR negates. RESET must remain asserted until the power
supplies are within the operating conditions as specified in
assert RESET before any power supplies fall outside the operating conditions and until the internal POR asserts.
V
to ‘Typical program and erase times are calculated at 25
frequency. Max speed is the maximum speed allowed including frequency modulation (FM). 82 MHz parts allow
for 80 MHz system clock + 2% FM; 114 MHz parts allow for 112 MHz system clock + 2% FM; and 132 MHz parts
allow for 128 MHz system clock + 2% FM.
DDE3
have a range of 1.6–3.6 V if SIU_ECCR[EBTS] =1.
A
= T
L
Table 28. Changes Between Rev. 2.0 and 3.0 (continued)
to T
DDEH
H
) to the table title.
DDEH
DDEH
DDEH
MPC5554 Microcontroller Data Sheet, Rev. 3.0
DD
DD
DD
DD
= 5.0 V, V
= 1.35–1.65 V.
= 1.35–1.65 V, and V
= 1.35–1.65 V, and V
= 1.35–1.65 V; changed V
DDE2
= 4.5–5.5;’ to ‘V
= 3.0–5.5 V to V
= 3.0–5.5 V to V
and V
DDE
A
= T
= 1.8 V)
DDE3
Description of Changes
L
to T
DDEH
are limited to 2.25–3.6 V only if SIU_ECCR[EBTS] = 0; V
DDEH
DDEH
H
DD33
DD33
)
= 4.5–5.25;’
= 3.0–5.25 V.
= 3.0–5.25 V.
DDEH
and V
and V
o
C operating temperature using nominal supply values..’
Table 9
= 3.0–5.5 V to V
DDSYN
DDSYN
Revision History for the MPC5554 Data Sheet
DC Electrical Specifications. On power down,
= 3.0–3.6 V.
= 3.0–3.6 V.
DDEH
POR15
= 3.0–5.25 V.
, V
POR33
, and V
DDE2
POR5
and
o
.
51
C’