FS-9003 Digi International, FS-9003 Datasheet - Page 60
FS-9003
Manufacturer Part Number
FS-9003
Description
JTAG-BOOSTER FOR XSCALE 3.3V
Manufacturer
Digi International
Series
Digi/FS Forthr
Type
FLASHr
Datasheet
1.FS-9003.pdf
(89 pages)
Specifications of FS-9003
Contents
Programmer and Associated Interface Software
For Use With/related Products
Intel XScale, 3.3V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 60 of 89
- Download datasheet (208Kb)
JTAG-Booster for Intel XScale
2.1.
Program a Flash Device
Usage:
JTAGxxx /P filename [optionlist]
The specified file is programmed into the flash memory. The flash status is
polled after programming of each cell (cell=8, 16 or 32 bit, depending on current
data bus width). In case of a programming error, the contents of the flash
memory is written to a file with the extension DMP.
If you want a complete verify after programming, please use an additional
command line with the verify function. See chapter 2.3 “Verify a Flash Device
with file”. In most cases this additional verify step is not needed.
The type of the flash device is normally detected by the software. When
autodetection fails you should use the /DEVICE= option together with /8BIT or
/16BIT or /32BIT to set the right flash device and configuration. The known flash
devices are shown in chapter 1.12 “Supported flash devices”.
Options:
/DEVICE=devicename
The flash device is detected automatically by switching to autoselect mode. In
case of trouble you should select the flash device by using this parameter to
avoid autodetection. Combine this option with one of the following options which
specify the data bus width and the option /BYTE-MODE if applicable.
/8BIT /16BIT /32BIT
Specifies the data bus width to the target flash device. You can speed up
autodetection, if you specify the correct data bus size. You need this option
together with the option /DEVICE= to explicit specify a specific flash
configuration.
/BYTE-MODE
If there is a flash device connected to the CPU which does have a byte mode pin
(8 bit and 16/32 bit bus mode), you can force it to be used as 8 bit mode with the
option /BYTE-MODE. In most cases this option will not be needed.
60
JTAG_XScaleb.doc
Related parts for FS-9003
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
JTAG SUPERBOOSTER FOR 5V FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG SUPERBOOSTER FOR 3V FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR IDT64145 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR SA-11X0 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR ELANSC520 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR ELANSC400 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR ADSP-21XXX 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR ARM7TDMI 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
JTAG-BOOSTER FOR S3C24XX 3.3V
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 7U 16MB SDRAM 8MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE UNC90 32MB SDRAM FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE A9M2410 32MB SDRAM FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 7U 16MB SDRAM 2MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE 7U 16MB SDRAM 8MB FLASH
Manufacturer:
Digi International
Datasheet: