Y92S-38 Omron, Y92S-38 Datasheet - Page 36

• Manufacturer Part Number: Y92S-38
• Description: LOCK KEY PEN FOR H3DS RELAYS
• Manufacturer: Omron
• Series: H3DSr

Specifications of Y92S-38

• Accessory Type: Tool - Lock Key Pen
• For Use With/related Products: H3DS Series
• For Use With: H3DS-SLCAC24-230/DC24 - TIMER CAGE CLAMP 17.5MM 4MODESH3DS-MLCAC24-230/DC24-48 - TIMER CAGE CLAMP 17.5MM 8MODESZ2395 - RELAY TIME DELAY 4MODE DIN MNTZ2394 - RELAY TIME DELAY 1MODE DIN MNTZ2393 - RELAY TIME DELAY 8MODE DIN MNTZ2392 - RELAY TIME DELAY 1MODE DIN MNT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Y92S38; Z2396

H3DS-G
Precautions
I
Do not change the time scale or operating mode while the Timer is
in operation, or malfunction could result.
I
The H3DS Series has a transformerless power supply system.
Touching the input terminal while power is being supplied can
cause you to get an electrical shock.
Use the bar terminal for wiring the H3DS. Using a stranded-wire
terminal may cause a short-circuit due to a stray wire entering into
the Timer.
Both AC and DC power supplies can be connected to the power
input terminals without regarding polarity.
With the H3DS only, a DC power supply must be connected to the
power input terminals as designated according to the polarity of
the terminals.
A DC power supply can be connected if its ripple factor is 20% or
less and the mean voltage is within the rated operating voltage
range of the Timer.
Make sure that the voltage is applied within the specified range, or
the internal elements of the Timer may be damaged.
Connect the power supply voltage through a relay or switch in
such a way that the voltage reaches a fixed value at once or the
Timer may not be reset or a timer error could result.
I
If the load current is continuously being supplied to the Timer for a
long period of time, be sure to provide the mounting clearance as
shown in the figure below. If used under conditions other than
those specified below, the life of internal components may be
shortened due to an excessive rise in the internal temperature.
Switching Current vs. Ambient Temperature
(When Mounting Two or More H3DS Units Side-by-Side)
H3DS-GL@ @ @ @
(Measurement Condition: Input voltage of 230 VAC)
Setting Changes
Power Supplies
Installation
!WARNING
!WARNING
!WARNING
!WARNING
H3DS
t
H3DS
t: Mounting clearance (mm)
t
Mounting clearance:
50 mm min.
Mounting clearance:
10 mm
Mounting clearance:
5 mm
Mounting clearance:
0 mm
Load current (A)
H3DS
Maximum range of
operating ambient
temperature
DIN track
I
The H3DS as a built-in timer conforms to EN61812-1 provided
that the following conditions are satisfied:
The output section of the H3DS is provided only with basic
isolation. To ensure reinforced isolation required by the
EN61812-1, provide supplementary basic isolation on the
load side connected to the output.
The H3DS itself is designed according to the following:
• Overvoltage category III
• Pollution degree 2
On the above basis:
Operation parts on the front and bottom: Reinforced isolation
–With clearance of 5.5 mm and creepage distance of 5.5 mm
at 230 VAC
Output: Basic isolation
–With clearance of 3 mm and creepage distance of 3 mm at
230 VAC
I
When using the Timer in an area with excess electrical noise,
separate the Timer, wiring, and the equipment which gener-
ates the input signals as far as possible from the noise
sources. Shield the input signal wiring to prevent electrical
interference.
Organic solvents (such as paint thinner), as well as very
acidic or basic solutions, can damage the outer casing of the
Timer.
Do not use the Timer in places where it is exposed to dust,
corrosive gas, or direct sunlight.
When storing the Timer, make sure that the ambient tempera-
ture and humidity are within the rated values. Leave the Timer
at room temperature for at least three hours before using the
Timer if it has been stored at an ambient temperature of
–10 ° C or below.
I
If the Timer is mounted on a control board, remove the Timer
from the control board or short-circuit the circuitry of the
power board before carrying out a voltage withstand test
between the electrical circuitry and non-current-carrying metal
part of the Timer, in order to prevent the internal circuitry of
the Timer from damage.
Precautions for EN61812-1
Conformance
Environment
Voltage Withstand Test
H3DS-G