G2R-1-DC24 Omron, G2R-1-DC24 Datasheet - Page 24

• Manufacturer Part Number: G2R-1-DC24
• Description: RELAY PWR SPDT 10A 24VDC PCB
• Manufacturer: Omron
• Series: G2Rr

Specifications of G2R-1-DC24

• Relay Type: General Purpose
• Contact Form: SPDT (1 Form C)
• Contact Rating (current): 10A
• Switching Voltage: 380VAC, 125VDC - Max
• Coil Type: Standard
• Coil Current: 21.8mA
• Coil Voltage: 24VDC
• Turn On Voltage (max): 16.8 VDC
• Turn Off Voltage (min): 3.6 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Circuit: SPDT (1 Form C)
• Contact Rating @ Voltage: 10A @ 250VAC
• Control On Voltage (max): 16.8 VDC
• Control Off Voltage (min): 3.6 VDC
• Coil Voltage Vdc Nom: 24V
• Contact Current Max: 10A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 1100ohm
• Contact Configuration: SPDT
• Current, Rating: 10 A
• Dielectric Rating: 5000 VAC @ 50⁄60 Hz (For 1 Minute Between Coil and Contacts)
• Dimensions: 1.14 in. L x 0.51 in. W x 1.40 in. H
• Function: Power
• Number Of Pins: 5
• Power, Rating: 2500⁄300 VA⁄W
• Resistance, Coil: 253 Ohms
• Standards: UL, CSA, VDE, CE
• Temperature, Operating, Maximum: 70 °C
• Temperature, Operating, Minimum: -40 °C
• Termination: Through Hole
• Voltage, Control: 24 VDC
• Voltage, Rating: 380 VAC
• Contact Rating: 10 A
• Contact Termination: Solder Pin
• Mounting Style: Through Hole
• Power Consumption: 530 mW
• Contact Material: Silver Alloy
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: G2R-1-DC24; G2R1DC24; Z2840

■ Driving by IC
An IC on which multiple driving transistors are integrated is available.
The designing of the circuit or PCB to drive multiple relays, a small-
size solenoid, or a small-size lamp can be simplified by using this IC.
Consult the manufacturer of the IC for details. For V
description of the related voltage and surge suppressor.
Dimensions Connection (Top view)
Equivalent circuit
■ Driving by TTL
TTLs can be divided into two types by classification of the output:
totem-pole and open-collector outputs. Connection of each type of
TTL is described below.
Use a diode as surge suppressor.
In the specifications of some ICs, such a phrase as “fan-out 10” may
be used in place of the legend I
TTLs can be connected in parallel. In terms of current, fan-out 1
equals 1.6 mA. Hence,
Fan-out n = 1.6 x n (mA)
1. To drive a relay by the totem-pole output of a TTL, these condi-
24
tions must be satisfied:
• I
• I
• Minimum supply voltage (4.75 V) – Maximum V
resistance.
(%)/Coil resistance
put voltage) > Lower-limit value of pickup voltage (Refer to Driv-
ing by Transistor)
OL
OH
(high-level output current) < Rated current x pickup voltage
(low-level output current) > Maximum supply voltage/Coil
Electromechanical Relays
GND
OL
. This denotes that 10 standard
I: Input (Base)
O: Output (Collector)
GND: (Common Emitter)
Technical Information
OL
GND
CE
(low-level out-
, refer to the
Totem-pole output
2. To drive a relay with open-collector output type TTL, a degree of
Open-collector output
The above description of the standard TTL is applicable when using
S, H, and LS type TTLs.
■ Driving by Other Switching
Consult the manufacturer of the switching device. The upper- and
lower-limit values of the pickup voltage can be determined in the
same manner as described in Upper-limit Pickup Voltage and Lower-
limit Pickup Voltage.
Example of Driving by SCR
freedom is allowed in the ratings of the relay coil. However, these,
conditions must be satisfied:
• I
• I
• V
• V
Devices
by Transistor.)
to Driving by Transistor.)
OL
OH
O
OL
> Maximum supply voltage to the relay coil/Coil resistance
= Dielectric strength of the output transistor (Refer to Driving
< Rated current x pickup voltage (%)/200
= Collector emitter voltage V
CE
of the output transistor (Refer