PR36MF12NSZF Sharp Microelectronics, PR36MF12NSZF Datasheet - Page 9
![RELAY SSR 240V .6A TRIAC 8-DIP](/photos/9/56/95669/pr36mf12nszf_sml.jpg)
PR36MF12NSZF
Manufacturer Part Number
PR36MF12NSZF
Description
RELAY SSR 240V .6A TRIAC 8-DIP
Manufacturer
Sharp Microelectronics
Series
PR36MFr
Datasheet
1.PR26MF11NIPF.pdf
(15 pages)
Specifications of PR36MF12NSZF
Circuit
SPST-NO (1 Form A)
Output Type
AC
Load Current
600mA
Voltage - Input
1.2VDC
Voltage - Load
0 ~ 240 V
Mounting Type
Through Hole
Termination Style
PC Pin
Package / Case
8-DIP (0.300", 7.62mm), 7 Leads
Load Voltage Rating
240 V
Mounting Style
Through Hole
Relay Type
Solid State
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
On-state Resistance
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
425-2369-5
■ Design Considerations
(
Output
∗
Operating temperature
) See Fig.2 about derating curve (I
Input
● Degradation
● Design guide
● Recommended Operating Conditions
In order for the SSR to turn off, the triggering current (I
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (I
voltage across the Triac, V
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs=0.022µF and Rs=47Ω. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
Input signal current
at ON state
Input signal current at OFF state
Load supply voltage
Load supply current
Frequency
Parameter
T
(rms) vs. ambient temperature).
PR26MF1xNSZ
PR36MF1xNSZ
Rank 1
Rank 2
F
) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
D
, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
V
I
I
OUT
Symbol
I
OUT
F
F
(OFF)
(ON)
T
(rms)
f
opr
(rms)
Locate snubber circuit between output terminals
9
(Cs=0.022µF, Rs=47Ω)
F
) must be 0.1mA or less.
Conditions
−
−
−
−
−
MIN.
PR26MF1xNSZ Series
PR36MF1xNSZ Series
−20
20
10
50
0
−
−
I
T
(rms)×80%(
Sheet No.: D4-A00401EN
MAX.
120
240
0.1
25
15
60
80
∗
)
Unit
mA
mA
mA
Hz
˚C
V