63811-7400 Molex Inc, 63811-7400 Datasheet - Page 4
![TOOL HAND CRIMP .156 TERM RACHET](/photos/9/85/98586/63811-7400_sml.jpg)
63811-7400
Manufacturer Part Number
63811-7400
Description
TOOL HAND CRIMP .156 TERM RACHET
Manufacturer
Molex Inc
Series
PremiumGrade™, KK®, Trifurcon™r
Type
Crimp Tool Assemblyr
Specifications of 63811-7400
Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Hand crimp tool assembly
Crimp Size
26AWG To 22AWG
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
Rectangular Contacts, 22-26 AWG
For Use With
WM2301TR - CONN TERM FEMALE 22-26AWG TINWM2306CT - CONN TERM FEMALE 22-26AWG GOLDWM2138 - CONN TERM FEMALE 22-26AWG GOLDWM2137TR - CONN TERM FEMALE 22-26AWG GOLDWM2136 - CONN TERM FEMALE 22-26AWG GOLDWM2314TR - CONN TERM FEMALE 22-26AWG TINWM2303TR - CONN TERM FEMALE 22-26AWG TINWM2306TR - CONN TERM FEMALE 22-26AWG GOLD08-50-0185 - CONN TERM CRIMP 22-26AWG TINWM2314 - CONN TERM FEMALE 22-26AWG TINWM2307 - CONN TERM FEMALE 22-26AWG GOLDWM2306 - CONN TERM FEMALE 22-26AWG GOLDWM2303 - CONN TERM FEMALE 22-26AWG TINWM2301 - CONN TERM FEMALE 22-26AWG TIN
Lead Free Status / Rohs Status
RoHS Exempt Product
Other names
063811-7400
063811-7400-E
0638117400
0638117400-E
63811-7400-E
638117400
638117400-E
WM9011
063811-7400-E
0638117400
0638117400-E
63811-7400-E
638117400
638117400-E
WM9011
Hand Crimp Tool for 3.96mm (.156") Pitch KK® Crimp Terminal
Doc No: ATS-638117400
Revision: B
Note:
A crimp height chart is provided with this manual as Reference
Only. Due to the wide range of wires, strands, insulation
diameters, and durometers, actual crimp height measurements
may very slightly. An occasional, destructive, pull force test
should be preformed to check hand tool crimp. Pull Force value
Must exceed the Minimum pull force specifications listed on page
2.
Locator Replacement
See the parts list on the last page of this document for the proper
locator order number. Follow the steps below to replace the locator.
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the hand tool.
3. Firmly press down on the brass pivot shaft with your thumb, while pulling the locator up. Slip the locator off the
4. Replace it with the proper locator by putting over the brass pivot shaft and snapping it into place.
Maintenance
It is recommended that each operator of the tool be made aware of,
and responsible for, the following maintenance steps:
1. Remove dust, moisture, and other contaminants with a clean
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are
4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position,
closed.
top of the brass pivot shaft. See Figure 4.
brush, or soft, lint free cloth.
protected with a thin coat of high quality machine oil. Do not oil
excessively. The tool was engineered for durability but like any
fine piece of equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping.
Light oil such as 30 weight automotive oil used at the oil points, every 5,000 crimps or 3 months, shown in
Figure 6 will significantly enhance the tool life.
certain terminations may affect the electrical characteristics of an application.
dies, and store the tool in a clean, dry area.
The tool will open easily by pressing the ratchet release lever. See Figure 6.
Release Date: 10-31-06
Revision Date: 04-08-08
UNCONTROLLED COPY
LOCATOR
ON BRASS PIVOT
SWING
OPEN
PRESS DOWN
SHAFT
Do Not force the handles open or
Figure 5
LOCATOR
LIFT UP
(BOTH SIDES) LIGHT OIL
LUBRICATION POINTS
(EVERY 3 MONTHS OR
5,000 CRIMPS)
Figure 4
Page 4 of 7
JAWS
OPEN