TCTAL1C226M8R Rohm Semiconductor, TCTAL1C226M8R Datasheet - Page 4

• Manufacturer Part Number: TCTAL1C226M8R
• Description: CAP TANTALUM 22UF 16V 20% SMD
• Manufacturer: Rohm Semiconductor
• Series: TCTr
• Type: Moldedr

Specifications of TCTAL1C226M8R

• Capacitance: 22µF
• Voltage - Rated: 16V
• Tolerance: ±20%
• Esr (equivalent Series Resistance): 4.000 Ohm
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 1206 (3216 Metric)
• Size / Dimension: 0.126" L x 0.063" W (3.20mm x 1.60mm)
• Height: 0.043" (1.10mm)
• Manufacturer Size Code: AL
• Features: General Purpose
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Other names: 511-1502-2

TCT Series AL Case
○
Temperature
Stability
Surge voltage
Loading at
High temperature
Terminal
strength
c
www.rohm.com
2009 ROHM Co., Ltd. All rights reserved.
Item
Temp.
∆C / C
Df (tan δ)
L.C.
Temp.
∆C / C
Df (tan δ)
L.C.
Temp.
∆C / C
Df (tan δ)
L.C.
Appearance
L.C.
∆C / C
Df (tan δ)
Appearance
L.C.
∆C / C
Df (tan δ)
Capacitance
Appearance
−55 °C
Within 0/−15% of initial value
Shall be satisfied the voltage on " Standard list "
+85 °C
Within +15/0% of initial value
Shall be satisfied the voltage on " Standard list "
5µA or 0.1CV whichever is greater
+125 °C
Within +20/0% of initial value
Shall be satisfied the voltage on " Standard list "
6.3µA or 0.125CV whichever is greater
There should be no significant abnormality.
Less than 200% of initial value
Within ±20% of initial value
Less than 200% of initial limit
There should be no significant abnormality.
Less than 200% of initial limit
Within ±20% of initial value
Less than 200% of initial limit
The measured value should be stable.
There should be no significant abnormality.
Performance
−
4/7
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 2000+72/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85±2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
thickness=1.6mm
50
45
R230
20
45
F (Apply force)
(Unit : mm)
1
2009.11 - Rev.H
Data Sheet