MCH185A1R5CK Rohm Semiconductor, MCH185A1R5CK Datasheet - Page 4
![CAP CERAMIC 1.5PF 50V C0G 0603](/photos/10/14/101474/mch18_series_0603_1608__sml.jpg)
MCH185A1R5CK
Manufacturer Part Number
MCH185A1R5CK
Description
CAP CERAMIC 1.5PF 50V C0G 0603
Manufacturer
Rohm Semiconductor
Datasheet
1.MCH183FN224ZK.pdf
(10 pages)
Specifications of MCH185A1R5CK
Capacitance
1.5pF
Voltage - Rated
50V
Tolerance
±0.25pF
Temperature Coefficient
C0G, NP0
Mounting Type
Surface Mount, MLCC
Operating Temperature
-55°C ~ 125°C
Features
General Purpose
Package / Case
0603 (1608 Metric)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
511-1091-2
Ceramic capacitors
!Characteristics
∗The design and specifications are subject to change without prior notice. Before ordering or using, please check the latest technical specification.
Class 1 (For thermal compensation)
Item
Temperature
cycling
Operating temperature
Nominal capacitance (C)
Dissipation factor (tan δ )
Insulation resistance (IR)
Withstanding voltage
Temperature characteristics
Terminal adherence
Resistance
to vibration
Solderability
Resistance
to soldering
heat
Humidity load
test
High-
temperature
load test
Temperature characteristics
Appearance
Rate of capacitance change
Dissipation factor (tanδ)
Appearance
Rate of capacitance change
Dissipation factor (tanδ)
Insulation resistance
Withstanding voltage
Appearance
Rate of capacitance change
Dissipation factor (tanδ)
Insulation resistance
Appearance
Rate of capacitance change
Dissipation factor (tanδ)
Insulation resistance
Appearance
Rate of capacitance change
Dissipation factor (tanδ)
Insulation resistance
10,000MΩ or 500ΜΩ⋅µF , whichever is smaller
At least 3 / 4 of the surface of the two terminals
10,000MΩ or 500ΜΩ⋅µF , whichever is smaller
10,000MΩ or 500ΜΩ⋅µF , whichever is smaller
1,000MΩ or 50ΜΩ⋅µF , whichever is smaller
Must be within the specified tolerance range.
500MΩ or 25ΜΩ⋅µF , whichever is smaller
± 2.5% or ± 0.25 pF , whichever is larger.
± 7.5% or ± 0.75 pF , whichever is larger.
± 3.0% or ± 0.3 pF , whichever is larger.
No detachment or signs of detachment.
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
± 2.5% ± 0.25 pF , whichever is larger.
There must be no mechanical damage.
There must be no mechanical damage.
The insulation must not be damaged.
The insulation must not be damaged.
Must satisfy initial specified value.
Must satisfy initial specified value.
Must satisfy initial specified value.
must be covered with new solder.
Must be within initial tolerance.
0.1% or less (30 pF or larger)
100 / (400 + 20C)% or less
Within 0 ± 30ppm / °C
(Less than 30 pF)
−55 °C ~ +125 °C
A (CG) (C0G)
0.5% or less
0.3% or less
Based on paragraph 7.8 and paragraph 9
Measured at room temperature and standard humidity.
1000pF or less Measurement frequency
Over 1000pF
Based on paragraph 7.6
Measurement is made after rated voltage
is applied for 60 ± 5s.
Based on paragraph 7.1
Apply 300% of the rated voltage
for 1 to 5s then measure.
The temperature coefficients in table 12, paragraph
7.12 are calculated at 20 °C and high temperature.
Based on paragraph 8.11.2
Apply 5N for 10 ± 1s
in the direction indicated
by the arrow.
Chip is mounted to a board in the
manner shown on the right, subjected
to vibration (type A in paragraph 8.2),
and measured 24 ± 2 hrs. later.
Based on paragraph 8.13
Based on paragraph 8.14
Based on paragraph 9.3
Based on paragraph 9.9
Based on paragraph 9.10
Soldering temperature
Soldering time
Soldering temperature
Soldering time
Preheating
Number of cycles : 5
Capacitance measured after 24 ± 2 hrs.
Test temperature : 40 ± 2 °C
Relative humidity
Applied voltage
Test time
Capacitance measured after 24 ± 2 hrs.
Test temperature
Applied voltage
Test time
Capacitance measured after 24 ± 2 hrs.
Test methods / conditions
(based on JIS C 5102)
Measurement voltage
Measurement frequency
Measurement voltage
: 90% to 95%
: rated voltage
: 500 to 524 hrs.
: Max. operating temp.
: rated voltage × 200%
: 1,000 to 1,048 hrs.
: 235 ± 5 °C
: 2 ± 0.5s
: 260 ± 5 °C
: 5 ± 0.5s
: 150 ± 10 °C for
Capacitor
1 to 2 min.
MCH18
Board
: 1± 0.1MHz
: 1± 0.1Vrms.
: 1± 0.1kHz
: 1± 0.1Vrms.
Pressure (5N)
Test board