K-HSTTA Panduit Corp, K-HSTTA Datasheet - Page 34

• Manufacturer Part Number: K-HSTTA
• Description: KIT HT SHRINK ADH 3/16"-1" BLK
• Manufacturer: Panduit Corp

PANDUIT
34
General Information
‡ Dimensions are approximate. Refer to the ordering information for exact Minimum Expanded and Maximum Recovered I.D
HSTT
HSTTV
HSTTR
HSTTVA
HSTTRA
HSTTA
HST
HSTTP
HSTTN
HSTTK
HSTTT
HSTTT4X
HSTTF
Product
Type
KYNAR is a registered trademark of ELF Atochem
®
FLEXIBLE
POL YOLEFIN
(Cross-linked)
HIGHLY FLEXIBLE
POL YOLEFIN
(Cross-linked)
SEMI-RIGID
POL YOLEFIN
(Cross-linked)
DUAL WALL
POL YOLEFIN
(Cross-linked)
DUAL WALL
POL YOLEFIN
(Cross-linked)
DUAL WALL
POL YOLEFIN
(Cross-linked)
HEAVY-WALL
DUAL WALL
POL YOLEFIN
(Cross-linked)
POL YVINYL
CHLORIDE – PVC
(Cross-linked/Heat
Shrinkable)
ELASTOMER
NEOPRENE
(Cross-linked)
FLUOROPLASTIC
KYNAR
(Cross-linked)
FLUOROPLASTIC
TEFLON (TFE) –
Polytetrafluorethylene
FLUOROPLASTIC
TEFLON
Polytetrafluorethylene
FLUOROPLASTIC
TEFLON (FEP) –
Fluorinated Ethylene
Propylene
D
Material
RY
-S
(TFE) –
HRINK
Temperature
275°F (135°C)
257°F (125°C)
275°F (135°C)
230°F (110°C)
230°F (110°C)
230°F (110°C)
230°F (110°C)
221°F (105°C)
250°F (121°C)
347°F (175°C)
482°F (250°C)
482°F (250°C)
392°F (200°C)
-67°F (-55°C)
-67°F (-55°C)
-67°F (-55°C)
-67°F (-55°C)
-67°F (-55°C)
-67°F (-55°C)
-85°F (-65°C)
-94°F (-70°C)
-67°F (-55°C)
-88°F (-67°C)
-88°F (-67°C)
-88°F (-67°C)
-4°F (-20°C)
Operating
Range
™
to
to
to
to
to
to
to
to
to
to
to
to
to
,
D
AMP
instructions
on
instructions
on
(329°C).
(329°C).
Shrink
Temp.
(120°C)
(135°C)
(121°C)
(200°C)
(121°C)
(121°C)
(121°C)
(135°C)
(176°C)
(176°C)
(85°C)
248°F
185°F
275°F
250°F
392°F
250°F
250°F
250°F
275°F
350°F
625°F
625°F
350°F
-S
page 29
page 29
See
See
T EF LON is a registered trademark of E.I. DuPont Co.
Technical Data
HRINK
Shrink
Ratio
2.5:1
1.3:1
2:1
2:1
2:1
2:1
3:1
3:1
2:1
2:1
2:1
2:1
4:1
‡
™
Longitudinal
and
Shrinkage
+10%
+20%
+20%
+15%
-10%
-10%
-15%
-10%
-20%
-10%
-10%
-20%
-20%
-15%
+5%
+1%
+5%
+1%
+1%
+1%
+1%
+1%
+1%
-5%
-5%
-5%
W
ET
-S
Economical and easy way to insulate, protect,
harness and identify electrical and electronic
components in a wide variety of applications.
Black is U.V. Resistant.
Use where UL recognition with VW-1 rating is
required. Use where the wire component
cannot tolerate higher shrink temperatures,
reduces application time to insulate, protect,
identify, etc. Black is U.V. Resistant.
Strain relief and insulation of soldered or
crimped connections when protection is
needed, tough covering for delicate
components, capacitor covers, diodes and
resistors. Black is U.V. Resistant.
Seals and protects components from
moisture and corrosion. Use where a flexible
tubing is needed. Suitable for damp locations.
Environmentally seals and protects
components forming a rugged and heavy duty
covering. The 2.5:1 shrink ratio is a benefit
when working with connector to cable
transitions. Encapsulated components.
Suitable for damp locations.
Environmentally seals and protects
components. The 3:1 shrink ratio is a benefit
when working with connector to cable
transitions. Encapsulated components.
Suitable for damp locations.
Seals and protects electrical connections and
splices above or below ground, 3:1 shrink
ratio. Suitable for outdoor and wet locations.
Ripple free conformance around sharp bends
as in appliance handles and bus bars. Good
cut through and solder-iron resistance.
Black is U.V. Resistant.
Insulation and abrasion resistance, extensive
military uses on vehicles and ship-board.
Excellent chemical resistant especially to
fuels and oils. Black is U.V. Resistant.
Protection and strain relief for wires or
connectors in a high temperature or solvent
rich environment. Insulation of heater leads.
High insulation and abrasion resistance. High
temperature, strain relief, resists corrosive
atmospheres, self lubrication and non-
wetting. Can be used with fiber optics and as
a strain relief for high density connectors.
U.V. Resistant
High insulation and abrasion resistance. High
temperature, strain relief, resists corrosive
atmospheres, self lubrication and non-
wetting. Can be used with fiber optics and as
a strain relief for high density connectors.
U.V. Resistant
All the advantages of TFE tubing plus the
advantage of a lower shrink temperature. Can
be used with fiber optics and as a strain relief
for high density connectors.
U.V. Resistant
HRINK
Typical Applications
™
Heat Shrink Tubing
Page
11-13
4-10
No.
14
20
22
21
23
15
16
19
17
17
18