ATTINY24-20MU Atmel, ATTINY24-20MU Datasheet - Page 167

• Manufacturer Part Number: ATTINY24-20MU
• Description: IC MCU AVR 2K FLASH 20MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY24-20MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-MLF®, QFN
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.6
8006K–AVR–10/10
High-voltage Serial Programming
If the LSB in RDY/BSY data byte out is ‘1’, a programming operation is still pending. Wait until
this bit returns ‘0’ before the next instruction is carried out.
Within the same page, the low data byte must be loaded prior to the high data byte.
After data is loaded to the page buffer, program the EEPROM page, see
166.
This section describes how to program and verify Flash Program memory, EEPROM Data mem-
ory, Lock bits and Fuse bits in the ATtiny24/44/84.
Figure 19-3. High-voltage Serial Programming
Table 19-13. Pin Name Mapping
The minimum period for the Serial Clock Input (SCI) during High-voltage Serial Programming is
220 ns.
Table 19-14. Pin Values Used to Enter Programming Mode
Signal Name in High-voltage
Serial Programming Mode
SDI
SII
SDO
SCI
Pin
PA0
PA1
PA2
SCI
+11.5 - 12.5V
Symbol
Prog_enable[0]
Prog_enable[1]
Prog_enable[2]
PB3
PB0
PA2:0
GND
PA5
Pin Name
PA6
PA4
PB0
(RESET)
I/O
O
I
I
I
VCC
PA4
PA5
PA6
Function
Serial Data Input
Serial Instruction Input
Serial Data Output
Serial Clock Input (min. 220ns period)
+4.5 - 5.5V
ATtiny24/44/84
SDO
SII
SDI
Figure 19-2 on page
Value
0
0
0
167