PIC18F4520-I/P Microchip Technology, PIC18F4520-I/P Datasheet - Page 37

• Manufacturer Part Number: PIC18F4520-I/P
• Description: IC MCU FLASH 16KX16 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4520-I/P

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: MSSP, SPI, I2C, PSP, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, 53275-917, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 3-1:
FIGURE 3-2:
3.2.3
In RC_RUN mode, the CPU and peripherals are
clocked from the internal oscillator block using the
INTOSC multiplexer. In this mode, the primary clock is
shut down. When using the INTRC source, this mode
provides the best power conservation of all the Run
modes while still executing code. It works well for user
applications which are not highly timing sensitive or do
not require high-speed clocks at all times.
If the primary clock source is the internal oscillator
block (either INTRC or INTOSC), there are no distin-
guishable
RC_RUN modes during execution. However, a clock
switch delay will occur during entry to and exit from
RC_RUN mode. Therefore, if the primary clock source
is the internal oscillator block, the use of RC_RUN
mode is not recommended.
© 2008 Microchip Technology Inc.
Peripheral
Note 1: Clock transition typically occurs within 2-4 T
Program
Counter
T1OSI
OSC1
Note1: T
Clock
Clock
RC_RUN MODE
CPU Clock
CPU
differences
PLL Clock
Peripheral
Program
Counter
Output
2: Clock transition typically occurs within 2-4 T
T1OSI
OSC1
Clock
Q1
OST
SCS<1:0> bits Changed
Q2
= 1024 T
TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE
TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL)
PC
Q3
between
Q4
OSC
; T
Q1
PLL
Q1
1
= 2 ms (approx). These intervals are not shown to scale.
T
PRI_RUN
OST
PC
(1)
2
Q2
Advance Information
Clock Transition
PIC18F2420/2520/4420/4520
OSTS bit Set
3
OSC
T
Q3
PLL
and
.
OSC
(1)
.
(1)
PC + 2
n-1
Q4
This mode is entered by setting the SCS1 bit to ‘1’.
Although it is ignored, it is recommended that the SCS0
bit also be cleared; this is to maintain software compat-
ibility with future devices. When the clock source is
switched to the INTOSC multiplexer (see Figure 3-3),
the primary oscillator is shut down and the OSTS bit is
cleared. The IRCF bits may be modified at any time to
immediately change the clock speed.
n
Q1
1
Note:
Transition
2
Clock
n-1 n
(2)
Q2
Caution should be used when modifying a
single IRCF bit. If V
possible to select a higher clock speed
than is supported by the low V
Improper device operation may result if
the V
PC + 2
DD
Q3
/F
Q2
OSC
Q4
Q3 Q4
specifications are violated.
Q1
DD
Q1
PC + 4
Q2
is less than 3V, it is
PC + 4
Q2
DS39631E-page 35
Q3
Q3
DD
.