ATMEGA16-16PU Atmel, ATMEGA16-16PU Datasheet - Page 288

• Manufacturer Part Number: ATMEGA16-16PU
• Description: IC AVR MCU 16K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Package: 40PDIP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 32
• Interface Type: TWI/SPI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• A/d Inputs: 8-Channel, 10-Bit
• Cpu Speed: 16 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 32
• Interface: JTAG/SPI/UART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin PDIP
• Programmable Memory: 16K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP44 - STK600 SOCKET/ADAPTER 44-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Programming
Algorithm
Entering Programming
Mode
Leaving Programming
Mode
Performing Chip Erase 1. Enter JTAG instruction PROG_COMMANDS.
Programming the
Flash
288
ATmega16(L)
All references below of type “1a”, “1b”, and so on, refer to
1. Enter JTAG instruction AVR_RESET and shift 1 in the Reset Register.
2. Enter instruction PROG_ENABLE and shift 1010_0011_0111_0000 in the Programming
1. Enter JTAG instruction PROG_COMMANDS.
2. Disable all programming instructions by using no operation instruction 11a.
3. Enter instruction PROG_ENABLE and shift 0000_0000_0000_0000 in the programming
4. Enter JTAG instruction AVR_RESET and shift 0 in the Reset Register.
2. Start chip erase using programming instruction 1a.
3. Poll for Chip Erase complete using programming instruction 1b, or wait for t
Before programming the Flash a Chip Erase must be performed.
on page 288.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load address High byte using programming instruction 2b.
4. Load address Low byte using programming instruction 2c.
5. Load data using programming instructions 2d, 2e and 2f.
6. Repeat steps 4 and 5 for all instruction words in the page.
7. Write the page using programming instruction 2g.
8. Poll for Flash write complete using programming instruction 2h, or wait for t
9. Repeat steps 3 to 7 until all data have been programmed.
A more efficient data transfer can be achieved using the PROG_PAGELOAD instruction:
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load the page address using programming instructions 2b and 2c. PCWORD (refer to
4. Enter JTAG instruction PROG_PAGELOAD.
5. Load the entire page by shifting in all instruction words in the page, starting with the LSB
6. Enter JTAG instruction PROG_COMMANDS.
7. Write the page using programming instruction 2g.
8. Poll for Flash write complete using programming instruction 2h, or wait for t
9. Repeat steps 3 to 8 until all data have been programmed.
Enable Register.
Enable Register.
to
Table 113 on page
Table 107 on page
of the first instruction in the page and ending with the MSB of the last instruction in the
page.
Table 113 on page
Table 113 on page
272).
262) is used to address within one page and must be written as 0.
272).
272).
Table
117.
See “Performing Chip Erase”
WLRH_CE
WLRH
WLRH
2466R–AVR–06/08
(refer to
(refer to
(refer