DSPIC30F4011-30I/PT Microchip Technology, DSPIC30F4011-30I/PT Datasheet - Page 85

• Manufacturer Part Number: DSPIC30F4011-30I/PT
• Description: IC DSPIC MCU/DSP 48K 44TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4011-30I/PT

• Program Memory Type: FLASH
• Program Memory Size: 48KB (16K x 24)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 30
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Data Rom Size: 1024 B
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM300018, DM330011
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44PT3 - SOCKET TRAN ICE 44MQFP/TQFPAC30F006 - MODULE SKT FOR DSPIC30F 44TQFPAC164305 - MODULE SKT FOR PM3 44TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: DSPIC30F401130IPT

13.4.2
The PWM period is specified by writing to the PRx reg-
ister. The PWM period can be calculated using
Equation 13-1.
EQUATION 13-1:
PWM frequency is defined as 1 / [PWM period].
FIGURE 13-1:
13.5
When the CPU enters the Sleep mode, all internal
clocks are stopped. Therefore, when the CPU enters
the Sleep state, the output compare channel will drive
the pin to the active state that was observed prior to
entering the CPU Sleep state.
For example, if the pin was high when the CPU
entered the Sleep state, the pin will remain high. Like-
wise, if the pin was low when the CPU entered the
Sleep state, the pin will remain low. In either case, the
output compare module will resume operation when
the device wakes up.
13.6
When the CPU enters the Idle mode, the output
compare module can operate with full functionality.
The output compare channel will operate during the
CPU Idle mode if the OCSIDL bit (OCxCON<13>) is at
logic 0 and the selected time base (Timer2 or Timer3)
is enabled and the TSIDL bit of the selected timer is
set to logic 0.
 2005 Microchip Technology Inc.
PWM period = [(PRx) + 1] • 4 • T
Output Compare Operation During
CPU Sleep Mode
Output Compare Operation During
CPU Idle Mode
PWM PERIOD
OCxR = OCxRS
TMR3 = PR3
(Interrupt Flag)
T3IF = 1
PWM PERIOD
(TMRx prescale value)
PWM OUTPUT TIMING
Duty Cycle
TMR3 = Duty Cycle (OCxR)
OSC
Period
•
Preliminary
OCxR = OCxRS
TMR3 = PR3
(Interrupt Flag)
T3IF = 1
When the selected TMRx is equal to its respective
period register, PRx, the following four events occur on
the next increment cycle:
• TMRx is cleared.
• The OCx pin is set.
• The PWM duty cycle is latched from OCxRS into
• The corresponding timer interrupt flag is set.
See Figure 13-1 for key PWM period comparisons.
Timer3 is referred to in the figure for clarity.
13.7
The output compare channels have the ability to gener-
ate an interrupt on a compare match, for whichever
Match mode has been selected.
For all modes except the PWM mode, when a compare
event occurs, the respective interrupt flag (OCxIF) is
asserted and an interrupt will be generated, if enabled.
The OCxIF bit is located in the corresponding IFS
Status register, and must be cleared in software. The
interrupt is enabled via the respective compare inter-
rupt enable (OCxIE) bit, located in the corresponding
IEC Control register.
For the PWM mode, when an event occurs, the respec-
tive timer interrupt flag (T2IF or T3IF) is asserted and
an interrupt will be generated, if enabled. The IF bit is
located in the IFS0 Status register, and must be cleared
in software. The interrupt is enabled via the respective
Timer Interrupt Enable bit (T2IE or T3IE), located in the
IEC0 Control register. The output compare interrupt
flag is never set during the PWM mode of operation.
TMR3 = Duty Cycle (OCxR)
- Exception 1: If PWM duty cycle is 0x0000,
- Exception 2: If duty cycle is greater than PRx,
OCxR.
dsPIC30F4011/4012
the OCx pin will remain low.
the pin will remain high.
Output Compare Interrupts
DS70135C-page 83