DSPIC30F4011-30I/ML Microchip Technology, DSPIC30F4011-30I/ML Datasheet - Page 7

• Manufacturer Part Number: DSPIC30F4011-30I/ML
• Description: IC DSPIC MCU/DSP 48K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4011-30I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 48KB (16K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 5.5V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 30
• Flash Memory Size: 48KB
• Supply Voltage Range: 2.5V To 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DSPIC30F401130IML

8. Module: DISI Instruction
9. Module: Output Compare in PWM Mode
© 2008 Microchip Technology Inc.
When a user executes a DISI #7, for example,
this will disable interrupts for 7 + 1 cycles (7 + the
DISI instruction itself). In this case, the DISI
instruction uses a counter which counts down from
7 to 0. The counter is loaded with 7 at the end of
the DISI instruction.
If the user code executes another DISI on the
instruction cycle where the DISI counter has
become zero, the new DISI count is loaded, but
the DISI state machine does not properly
re-engage and continue to disable interrupts. At
this point, all interrupts are enabled. The next time
the user code executes a DISI instruction, the
feature will act normally and block interrupts.
In summary, it is only when a DISI execution is
coincident with the current DISI count = 0, that
the issue occurs. Executing a DISI instruction
before the DISI counter reaches zero will not
produce this error. In this case, the DISI counter
is loaded with the new value, and interrupts
remain disabled until the counter becomes zero.
Work around
When executing multiple DISI instructions within
the source code, make sure that subsequent DISI
instructions have at least one instruction cycle
between the time that the DISI counter
decrements to zero and the next DISI instruction.
Alternatively, make sure that subsequent DISI
instructions are called before the DISI counter
decrements to zero.
If the desired duty cycle is ‘0’ (OCxRS = 0), the
module will generate a high level glitch of 1 T
The second problem is that on the next cycle after
the glitch, the OC pin does not go high, or in other
words, it misses the next compare for any value
written on OCxRS.
Work around
There are two possible solutions to this problem:
1. Load a value greater than ‘0’ to the OCxRS
2. If the application requires 0% duty cycles, the
register when operating in PWM mode. In this
case, no 0% duty cycle is achievable.
output compare module can be disabled
for 0% duty cycles, and re-enabled for
non-zero percent duty cycles.
CY
.
10. Module: Output Compare
11. Module: INT0, ADC and Sleep Mode
12. Module: 8x PLL Mode
dsPIC30F4011/4012
A glitch will be produced on an output compare pin
under the following conditions:
• The user software initially drives the I/O pin
• The output compare module is configured and
When these events occur, the output compare
module will drive the pin low for one instruction
cycle (T
Work around
None. However, the user may use a timer interrupt
and write to the associated PORT register to
control the pin manually.
ADC event triggers from the INT0 pin will not
wake-up the device from Sleep mode if the SMPI
bits are non-zero. This means that if the ADC is
configured to generate an interrupt after a certain
number of INT0 triggered conversions, the ADC
conversions will not be triggered and the device
will remain in Sleep. The ADC will perform
conversions and wake-up the device only if it is
configured to generate an interrupt after each INT0
triggered conversion (SMPI<3:0> = 0000).
Work around
None. If ADC event trigger from the INT0 pin is
required, initialize SMPI<3:0> to ‘0000’ (interrupt
on every conversion).
If 8x PLL mode is used, the input frequency range
is 5 MHz-10 MHz instead of 4 MHz-10 MHz.
Work around
None. If 8x PLL is used, make sure the input
crystal or clock frequency is 5 MHz or greater.
high using the output compare module or a
write to the associated PORT register.
enabled to drive the pin low at some later time
(OCxCON = 0x0002 or OCxCON = 0x0003).
CY
) after the module is enabled.
DS80398A-page 7