DSPIC33FJ128MC804-I/PT Microchip Technology, DSPIC33FJ128MC804-I/PT Datasheet - Page 303

• Manufacturer Part Number: DSPIC33FJ128MC804-I/PT
• Description: IC DSPIC MCU/DSP 128K 44TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC804-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 35
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 9x10b/12b, D/A 6x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC33F
• Core: dsPIC
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Data Ram Size: 16 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DV164033
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

27.2
All
dsPIC33FJ64GPX02/X04, and dsPIC33FJ128GPX02/
X04 devices power their core digital logic at a nominal
2.5V. This can create a conflict for designs that are
required to operate at a higher typical voltage, such as
3.3V. To simplify system design, all devices in the
dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04,
and dsPIC33FJ128GPX02/X04 family incorporate an
on-chip regulator that allows the device to run its core
logic from V
The regulator provides power to the core from the other
V
(less than 5 Ohms) capacitor (such as tantalum or
ceramic) must be connected to the V
(Figure
regulator. The recommended value for the filter capac-
itor is provided in
“DC
On a POR
voltage regulator to generate an output voltage. During
this time, designated as T
disabled. T
resumes operation after any power-down.
FIGURE 27-1:
© 2011 Microchip Technology Inc.
DD
dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04, AND dsPIC33FJ128GPX02/X04
Note:
Note 1: These are typical operating voltages. Refer
pins. When the regulator is enabled, a low-ESR
Characteristics”.
Tantalum
27-1). This helps to maintain the stability of the
10 µF
C
On-Chip Voltage Regulator
of
,
EFC
2: It is important for the low-ESR capacitor to
STARTUP
it takes approximately 20 μs for the on-chip
It is important for the low-ESR capacitor to
be placed as close as possible to the V
pin.
DD
to
“DC Characteristics”
ranges of V
be placed as close as possible to the V
pin.
.
3.3V
Table
Table 30-13
the
is applied every time the device
CONNECTIONS FOR THE
ON-CHIP VOLTAGE
REGULATOR
30-13, located in
V
V
V
DD
DD
CAP
SS
dsPIC33F
STARTUP
and V
dsPIC33FJ32GP302/304,
located in
CAP
for the full operating
, code execution is
.
(1)
Section 30.1
Section 30.1
CAP
CAP
CAP
pin
27.3
The Brown-out Reset (BOR) module is based on an
internal voltage reference circuit that monitors the reg-
ulated supply voltage V
BOR module is to generate a device Reset when a
brown-out condition occurs. Brown-out conditions are
generally caused by glitches on the AC mains (for
example, missing portions of the AC cycle waveform
due to bad power transmission lines, or voltage sags
due to excessive current draw when a large inductive
load is turned on).
A BOR generates a Reset pulse, which resets the
device. The BOR selects the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>).
If an oscillator mode is selected, the BOR activates the
Oscillator Start-up Timer (OST). The system clock is
held until OST expires. If the PLL is used, the clock is
held until the LOCK bit (OSCCON<5>) is ‘1’.
Concurrently, the PWRT time-out (TPWRT) is applied
before the internal Reset is released. If TPWRT = 0 and
a crystal oscillator is being used, then a nominal delay
of TFSCM = 100 is applied. The total delay in this case
is TFSCM.
The BOR Status bit (RCON<1>) is set to indicate that a
BOR has occurred. The BOR circuit continues to oper-
ate while in Sleep or Idle modes and resets the device
should VDD fall below the BOR threshold voltage.
BOR: Brown-out Reset
CAP
. The main purpose of the
DS70292E-page 303