PIC16C71/JW Microchip Technology, PIC16C71/JW Datasheet - Page 91

• Manufacturer Part Number: PIC16C71/JW
• Description: IC MCU EPROM 1KX14 A/D 18CDIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C71/JW

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 13
• Program Memory Size: 1.75KB (1K x 14)
• Program Memory Type: EPROM, UV
• Ram Size: 36 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 4x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-CDIP (0.300", 7.62mm) Window
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Connectivity: -
• Other names: PIC16C71-16/JW; PIC16C71-16/JW; PIC16C71-20/JW

11.2
DC CHARACTERISTICS
D001
D002*
D003
D004*
D005
D010
D010A
D015
D020
D021
D021A
D021B
D023
Note 1: This is the limit to which V
Param
1997 Microchip Technology Inc.
No.
*
†
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
5: The
DC Characteristics:
These parameters are characterized but not tested.
and are not tested.
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
MCLR = V
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
mated by the formula Ir = V
added to the base I
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
Supply Voltage
RAM Data Retention
Voltage (Note 1)
V
ensure internal Power-
on Reset signal
V
internal Power-on
Reset
signal
Brown-out Reset
Voltage
Supply Current
(Note 2)
Brown-out Reset
Current (Note 5)
Power-down Current
(Note 3)
Brown-out Reset
Current (Note 5)
Commercial/Industrial
Extended
DD
DD
Characteristic
start voltage to
rise rate to ensure
current is the additional current consumed when this peripheral is enabled. This current should be
DD
; WDT enabled/disabled as specified.
DD
or I
PD
DD
PIC16LC710-04 (Commercial, Industrial, Extended)
PIC16LC711-04 (Commercial, Industrial, Extended)
DD
DD
V
S
B
Sym
V
V
V
I
I
I
I
measurement.
POR
can be lowered without losing RAM data.
VDD
VDD
DD
BOR
PD
BOR
measurements in active operation mode are:
/2Rext (mA) with Rext in kOhm.
DD
DD
DR
Standard Operating Conditions (unless otherwise stated)
Operating temperature
0.05
Min
2.5
3.0
3.7
-
-
-
-
-
-
-
-
-
-
Typ† Max Units
300*
300*
22.5
V
1.5
4.0
2.0
7.5
0.9
0.9
0.9
SS
-
-
-
500
500
6.0
6.0
3.8
4.3
48
30
10
5
5
-
-
-
V/ms See section on Power-on Reset for details
mA
V
V
V
V
V
A
A
A
A
A
A
A
0˚C
-40˚C
-40˚C
Applicable Devices
LP, XT, RC osc configuration (DC - 4 MHz)
LP, XT, RC osc configuration (DC - 4 MHz)
See section on Power-on Reset for details
BODEN configuration bit is enabled
XT, RC osc configuration
F
LP osc configuration
F
BOR enabled V
V
V
V
V
BOR enabled V
OSC
OSC
DD
DD
DD
DD
= 3.0V, WDT enabled, -40 C to +85 C
= 3.0V, WDT disabled, 0 C to +70 C
= 3.0V, WDT disabled, -40 C to +85 C
= 3.0V, WDT disabled, -40 C to +125 C
= 4 MHz, V
= 32 kHz, V
T
T
T
A
A
A
+70˚C (commercial)
+85˚C (industrial)
+125˚C (extended)
DD
PIC16C71X
DD
DD
Conditions
DD
DD
= 5.0V
= 5.0V
= 3.0V (Note 4)
= 3.0V, WDT disabled
710 71 711 715
DS30272A-page 91
DD
and V
SS
.