C8051F326-GM Silicon Laboratories Inc, C8051F326-GM Datasheet - Page 76

• Manufacturer Part Number: C8051F326-GM
• Description: IC 8051 MCU FLASH 16K 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F326-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART, USB
• Peripherals: POR
• Number Of I /o: 15
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 15
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 2
• Digital Ic Case Style: QFN
• Supply Voltage: RoHS Compliant
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F326
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1450 - ADAPTER PROGRAM TOOLSTICK F326336-1306 - KIT DEV FOR C8051F326/7
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1296-5

C8051F326/7
10.5. System and USB Clock Selection
The internal oscillator requires little start-up time and may be selected as the system or USB clock immedi-
ately following the OSCICN write that enables the internal oscillator. If the external clock is selected as the
system or USB clock, then startup times may vary based on the specifications of the external clock.
10.5.1. System Clock Selection
The CLKSL[2:0] bits in register CLKSEL select which oscillator source is used as the system clock.
CLKSL[2:0] must be set to 001b for the system clock to run from the external clock; however the external
clock may still clock certain peripherals (timers, UART, USB) when the internal oscillator is selected as the
system clock. The system clock may be switched on-the-fly between the internal oscillator, external clock,
low frequency oscillator, and 4x Clock Multiplier so long as the selected oscillator is enabled and can pro-
vide a stable clock.
10.5.2. USB Clock Selection
The USBCLK[1:0] bits in register CLKSEL select which oscillator source is used as the USB clock. The
USB clock may be derived from the 4x Clock Multiplier output, internal oscillator divided by 2, or an exter-
nal clock. The USB clock source may also be turned off. The USB clock must be 48 MHz when operating
USB0 as a Full Speed Function; the USB clock must be 6 MHz when operating USB0 as a Low Speed
Function. See Figure 10.5 for USB clock selection options.
Some example USB clock configurations for Full and Low Speed mode are given below:
76
USB Clock
Clock Multiplier Input
Internal Oscillator
USB Clock
Clock Multiplier Input
Port I/O
*Note: Clock Recovery must be enabled for this configuration.
USB Clock
Internal Oscillator
USB Clock
Port I/O
Clock Signal
Clock Signal
Clock Signal
Clock Signal
Table 10.2. Typical USB Low Speed Clock Settings
Table 10.1. Typical USB Full Speed Clock Settings
Clock Multiplier
Internal Oscillator*
Divide by 1
Clock Multiplier
External Clock
12 MHz CMOS Clock
Internal Oscillator / 2
Divide by 1
External Clock
6 MHz CMOS Clock
Input Source Selection
Input Source Selection
Input Source Selection
Input Source Selection
Internal Oscillator
Internal Oscillator
External Clock
External Clock
Rev. 1.1
USBCLK = 00b
MULSEL = 0b
IFCN = 11b
USBCLK = 10b
MULSEL = 1b
INPUTEN = 1b (GPI-
OCN.6)
USBCLK = 01b
IFCN = 11b
USBCLK = 10b
INPUTEN = 1b (GPI-
OCN.6)
Register Bit Settings
Register Bit Settings
Register Bit Settings
Register Bit Settings