C8051F704-GM Silicon Laboratories Inc, C8051F704-GM Datasheet - Page 67

• Manufacturer Part Number: C8051F704-GM
• Description: IC 8051 MCU 15K FLASH 48-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F70xr

Specifications of C8051F704-GM

• Program Memory Type: FLASH
• Program Memory Size: 15KB (15K x 8)
• Package / Case: 48-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Cap Sense, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 39
• Eeprom Size: 32 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F7x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 39
• Number Of Timers: 4 x 16 bit
• Operating Supply Voltage: 1.8 V to 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F700DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1635 - DEV KIT FOR C8051F700
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1610-5

11. Temperature Sensor
An on-chip temperature sensor is included on the C8051F700/2/4/6/8 and C8051F710/2/4/6 which can be
directly accessed via the ADC multiplexer in single-ended configuration. To use the ADC to measure the
temperature sensor, the ADC mux channel should be configured to connect to the temperature sensor.
The temperature sensor transfer function is shown in Figure 11.1. The output voltage (V
tive ADC input when the ADC multiplexer is set correctly. The TEMPE bit in register REF0CN enables/dis-
ables the temperature sensor, as described in SFR Definition 12.1. While disabled, the temperature sensor
defaults to a high impedance state and any ADC measurements performed on the sensor will result in
meaningless data. Refer to Table 9.12 for the slope and offset parameters of the temperature sensor.
11.1. Calibration
The uncalibrated temperature sensor output is extremely linear and suitable for relative temperature mea-
surements (see Table 5.1 for linearity specifications). For absolute temperature measurements, offset
and/or gain calibration is recommended. Typically a 1-point (offset) calibration includes the following steps:
1. Control/measure the ambient temperature (this temperature must be known).
2. Power the device, and delay for a few seconds to allow for self-heating.
3. Perform an ADC conversion with the temperature sensor selected as the ADC’s input.
4. Calculate the offset characteristics, and store this value in non-volatile memory for use with subsequent
Figure 5.3 shows the typical temperature sensor error assuming a 1-point calibration at 0 °C.
temperature sensor measurements.
Figure 11.1. Temperature Sensor Transfer Function
V
Temp
TEMP
C
=
= (V
(Slope
TEMP
x Temp
- Offset) /
Temperature
Rev. 1.0
C
) +
Offset
Slope
Offset
(V at 0 Celsius)
Slope
C8051F70x/71x
(V / deg C)
TEMP
) is the posi-
67