PIC16F684-E/P Microchip Technology, PIC16F684-E/P Datasheet - Page 115

• Manufacturer Part Number: PIC16F684-E/P
• Description: IC PIC MCU FLASH 2KX14 14DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F684-E/P

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 14-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163029 - BOARD PICDEM FOR MECHATRONICSACICE0207 - MPLABICE 14P 300 MIL ADAPTER
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 12-10:
12.8
If
programmed, the on-chip program memory can be
read out using ICSP
12.9
Four memory locations (2000h-2003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution but are
readable and writable during Program/Verify mode.
Only the Least Significant 7 bits of the ID locations are
used.
© 2007 Microchip Technology Inc.
Instruction Flow
(INTCON reg.)
(INTCON reg.)
Note:
Instruction
Fetched
Instruction
Executed
the
CLKOUT
Note 1:
INTF flag
INT pin
GIE bit
OSC1
Code Protection
ID Locations
code
PC
2:
3:
4:
(4)
The entire data EEPROM and Flash pro-
gram memory will be erased when the
code protection is turned off. See the
“PIC12F6XX/16F6XX Memory
Programming Specification” (DS41204)
for more information.
XT, HS or LP Oscillator mode assumed.
T
GIE = ‘1’ assumed. In this case after wake-up, the processor jumps to 0004h. If GIE = ‘0’, execution will continue in-line.
CLKOUT is not available in XT, HS, LP or EC Oscillator modes, but shown here for timing reference.
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Inst(PC) = Sleep
OST
protection
Inst(PC – 1)
= 1024 T
PC
™
WAKE-UP FROM SLEEP THROUGH INTERRUPT
for verification purposes.
OSC
(drawing not to scale). This delay does not apply to EC, INTOSC and RC Oscillator modes.
bit(s)
Inst(PC + 1)
Sleep
PC + 1
have
Processor in
not
Sleep
PC + 2
been
T
OST (2)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Interrupt Latency
Inst(PC + 2)
Inst(PC + 1)
PC + 2
(3)
Dummy Cycle
PC + 2
Dummy Cycle
PIC16F684
Inst(0004h)
0004h
DS41202F-page 113
Inst(0005h)
Inst(0004h)
0005h