ATTINY261A-MN Atmel, ATTINY261A-MN Datasheet - Page 180

• Manufacturer Part Number: ATTINY261A-MN
• Description: IC MCU AVR 2K FLASH 32QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY261A-MN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATtiny
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 128 B, 256 B, 512 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 105 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.7.7
180
ATtiny261A/461A/861A
Reading the Flash
programmed simultaneously. The programming algorithm for the EEPROM data memory is as
follows (refer to
Data loading):
Figure 18-6. Programming the EEPROM Waveforms
The algorithm for reading the Flash memory is as follows (refer to
page 177
RESET +12V
1. A: Load Command “0001 0001”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. C: Load Data (0x00 - 0xFF).
5. E: Latch data (give PAGEL a positive pulse).
6. K: Repeat 3 through 5 until the entire buffer is filled.
7. L: Program EEPROM page
1. A: Load Command “0000 0010”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. Set OE to “0”, and BS1 to “0”. The Flash word low byte can now be read at DATA.
5. Set BS to “1”. The Flash word high byte can now be read at DATA.
6. Set OE to “1”.
PAGEL/BS1
RDY/BSY
XA1/BS2
XTAL1
DATA
a. Set BS to “0”.
b. Give WR a negative pulse. This starts programming of the EEPROM page.
c. Wait until to RDY/BSY goes high before programming the next page (See
XA0
WR
OE
RDY/BSY goes low.
18-6
for details on Command and Address loading):
for signal waveforms).
0x11
A
“Programming the Flash” on page 177
ADDR. HIGH
G
ADDR. LOW
B
DATA
C
XX
E
ADDR. LOW
B
for details on Command, Address and
DATA
C
K
XX
E
“Programming the Flash” on
L
8197B–AVR–01/10
Figure