PIC16LC62B-04/SS Microchip Technology, PIC16LC62B-04/SS Datasheet - Page 63

• Manufacturer Part Number: PIC16LC62B-04/SS
• Description: IC MCU OTP 2KX14 PWM 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC62B-04/SS

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -

10.10.1 INT INTERRUPT
The external interrupt on RB0/INT pin is edge trig-
gered: either rising, if bit INTEDG (OPTION_REG<6>)
is set, or falling, if the INTEDG bit is clear. When a valid
edge appears on the RB0/INT pin, flag bit INTF
(INTCON<1>) is set. This interrupt can be disabled by
clearing enable bit INTE (INTCON<4>). Flag bit INTF
must be cleared in software in the interrupt service rou-
tine before re-enabling this interrupt. The INT interrupt
can wake-up the processor from SLEEP, if bit INTE was
set prior to going into SLEEP. The status of global inter-
rupt enable bit GIE decides whether or not the proces-
sor branches to the interrupt vector following wake-up.
See Section 10.13 for details on SLEEP mode.
10.10.2 TMR0 INTERRUPT
An overflow (FFh
flag bit T0IF (INTCON<2>). The interrupt can be
enabled/disabled by setting/clearing enable bit T0IE
(INTCON<5>). (Section 4.0)
10.10.3 PORTB INTCON CHANGE
An input change on PORTB<7:4> sets flag bit RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit RBIE (INTCON<4>).
(Section 3.2)
EXAMPLE 10-1: SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
1999 Microchip Technology Inc.
MOVWF
SWAPF
CLRF
MOVWF
:
:(ISR)
:
SWAPF
MOVWF
SWAPF
SWAPF
W_TEMP
STATUS,W
STATUS
STATUS_TEMP
STATUS_TEMP,W
STATUS
W_TEMP,F
W_TEMP,W
00h) in the TMR0 register will set
;Copy W to TEMP register, could be bank one or zero
;Swap status to be saved into W
;bank 0, regardless of current bank, Clears IRP,RP1,RP0
;Save status to bank zero STATUS_TEMP register
;Swap STATUS_TEMP register into W
;(sets bank to original state)
;Move W into STATUS register
;Swap W_TEMP
;Swap W_TEMP into W
Preliminary
10.11
During an interrupt, only the return PC value is saved
on the stack. Typically, users may wish to save key reg-
isters during an interrupt, (i.e., W register and STATUS
register). This will have to be implemented in software.
Example 10-1 stores and restores the W and STATUS
registers. The register, W_TEMP, must be defined in
each bank and must be defined at the same offset from
the bank base address (i.e., if W_TEMP is defined at
0x20 in bank 0, it must also be defined at 0xA0 in bank
1).
The example:
a)
b)
c)
d)
e)
f)
Stores the W register.
Stores the STATUS register in bank 0.
Stores the PCLATH register.
Executes the interrupt service routine code
(User-generated).
Restores the STATUS register (and bank select
bit).
Restores the W and PCLATH registers.
Context Saving During Interrupts
PIC16C62B/72A
DS35008B-page 63