PIC16F916-I/SP Microchip Technology, PIC16F916-I/SP Datasheet - Page 130

• Manufacturer Part Number: PIC16F916-I/SP
• Description: IC PIC MCU FLASH 8KX14 28SDIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F916-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 352 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 352 B
• Interface Type: SSP/I2C/AUSART/SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F91X
REGISTER 11-2:
DS41250B-page 128
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
RCSTA – RECEIVE STATUS AND CONTROL REGISTER (ADDRESS 18h)
bit 7
SPEN
1 = Serial port enabled (configures RC7/RX/DT/SDI/SDA/SEG8 and
0 = Serial port disabled
RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete
Synchronous mode – Slave:
Don’t care.
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables continuous receive
0 = Disables continuous receive
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and load of the receive buffer when RSR<8>
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG register and receive next valid byte)
0 = No framing error
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
Legend:
R = Readable bit
- n = Value at POR
OERR: Overrun Error bit
RX9D: 9th bit of Received Data (can be parity bit but must be calculated by user firmware)
R/W-0
SPEN
Note 1: CCP2CON used for PIC16F914/917 only.
RC6/TX/CK/SCK/SCL/SEG9 pins as serial port pins)
is set
(1)
: Serial Port Enable bit
R/W-0
RX9
R/W-0
SREN
Preliminary
W = Writable bit
‘1’ = Bit is set
R/W-0
CREN
ADDEN
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
FERR
R-0
 2004 Microchip Technology Inc.
x = Bit is unknown
OERR
R-0
RX9D
R-x
bit 0