DSPIC33FJ64GP710-I/PT Microchip Technology, DSPIC33FJ64GP710-I/PT Datasheet - Page 173

• Manufacturer Part Number: DSPIC33FJ64GP710-I/PT
• Description: IC DSPIC MCU/DSP 64K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ64GP710-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: DCI, ECAN, I2C, SPI, UART
• No. Of I/o's: 85
• Flash Memory Size: 64KB
• Supply Voltage Range: 3V To 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164333 - MODULE SKT FOR PM3 100QFPDM300024 - KIT DEMO DSPICDEM 1.1DV164033 - KIT START EXPLORER 16 MPLAB ICD2MA330012 - MODULE DSPIC33 100P TO 84QFPMA330011 - MODULE DSPIC33 100P TO 100QFPDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

16.0
The Serial Peripheral Interface (SPI) module is a
synchronous serial interface useful for communicating
with other peripheral or microcontroller devices. These
peripheral devices may be serial EEPROMs, shift
registers, display drivers, ADC, etc. The SPI module is
compatible with SPI and SIOP from Motorola
FIGURE 16-1:
© 2009 Microchip Technology Inc.
Note:
Note:
SDOx
SCKx
SDIx
SSx
SERIAL PERIPHERAL
INTERFACE (SPI)
This data sheet summarizes the features
of the dsPIC33FJXXXGPX06/X08/X10
family of devices. However, it is not
intended to be a comprehensive reference
source. To complement the information in
this data sheet, refer to Section 18.
“Serial
(DS70206) in the “dsPIC33F Family
Reference Manual”, which is available
from
(www.microchip.com).
In this section, the SPI modules are
referred to together as SPIx, or separately
as SPI1 and SPI2. Special Function
Registers will follow a similar notation. For
example, SPIxCON refers to the control
register for the SPI1 or SPI2 module.
Read SPIxBUF
Control
Sync
Transfer
the
Peripheral
SPI MODULE BLOCK DIAGRAM
Microchip
SPIxRXB
bit 0
SPIxBUF
SPIxSR
Control
Interface
Clock
dsPIC33FJXXXGPX06/X08/X10
Shift Control
SPIxTXB
web
®
.
(SPI)”
Transfer
Write SPIxBUF
site
Select
Edge
Each SPI module consists of a 16-bit shift register,
SPIxSR (where x = 1 or 2), used for shifting data in and
out, and a buffer register, SPIxBUF. A control register,
SPIxCON, configures the module. Additionally, a status
register, SPIxSTAT, indicates various status conditions.
The serial interface consists of 4 pins: SDIx (serial data
input), SDOx (serial data output), SCKx (shift clock input
or output), and SSx (active-low slave select).
In Master mode operation, SCK is a clock output but in
Slave mode, it is a clock input.
16
Secondary
1:1 to 1:8
Prescaler
Internal Data Bus
1:1/4/16/64
Prescaler
Primary
F
SPIxCON1<1:0>
SPIxCON1<4:2>
Enable
Master Clock
DS70286C-page 171
CY