DSPIC33FJ64GP710-I/PT Microchip Technology, DSPIC33FJ64GP710-I/PT Datasheet - Page 20

• Manufacturer Part Number: DSPIC33FJ64GP710-I/PT
• Description: IC DSPIC MCU/DSP 64K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ64GP710-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: DCI, ECAN, I2C, SPI, UART
• No. Of I/o's: 85
• Flash Memory Size: 64KB
• Supply Voltage Range: 3V To 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164333 - MODULE SKT FOR PM3 100QFPDM300024 - KIT DEMO DSPICDEM 1.1DV164033 - KIT START EXPLORER 16 MPLAB ICD2MA330012 - MODULE DSPIC33 100P TO 84QFPMA330011 - MODULE DSPIC33 100P TO 100QFPDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC33FJXXXGPX06/X08/X10
FIGURE 2-1:
2.2.1
On boards with power traces running longer than six
inches in length, it is suggested to use a tank capacitor
for integrated circuits including DSCs to supply a local
power source. The value of the tank capacitor should
be determined based on the trace resistance that con-
nects the power supply source to the device, and the
maximum current drawn by the device in the applica-
tion. In other words, select the tank capacitor so that it
meets the acceptable voltage sag at the device. Typical
values range from 4.7 µF to 47 µF.
2.3
A low-ESR (< 5 Ohms) capacitor is required on the
V
voltage regulator output voltage. The V
pin must not be connected to V
capacitor between 4.7 µF and 10 µF, 16V connected to
ground. The type can be ceramic or tantalum. Refer to
Section 25.0
additional information.
The placement of this capacitor should be close to the
V
length not exceed one-quarter inch (6 mm). Refer to
Section 22.2 “On-Chip Voltage Regulator” for
details.
DS70286C-page 18
CAP
CAP
Ceramic
V
0.1 µF
DD
R
/V
/V
C
DDCORE
DDCORE
R1
Capacitor on Internal Voltage
Regulator (V
TANK CAPACITORS
10
MCLR
V
V
SS
DD
. It is recommended that the trace
“Electrical
pin, which is used to stabilize the
RECOMMENDED
MINIMUM CONNECTION
dsPIC33F
CAP
Ceramic
0.1 µF
/V
Characteristics”
DD
DDCORE
, and must have a
V
V
CAP
DD
SS
Ceramic
0.1 µF
Ceramic
0.1 µF
)
/V
Ceramic
0.1 µF
DDCORE
for
2.4
The MCLR pin provides for two specific device
functions:
• Device Reset
• Device programming and debugging
During device programming and debugging, the
resistance and capacitance that can be added to the
pin must be considered. Device programmers and
debuggers drive the MCLR pin. Consequently,
specific voltage levels (V
transitions must not be adversely affected. Therefore,
specific values of R and C will need to be adjusted
based on the application and PCB requirements.
For
recommended that the capacitor C, be isolated from
the MCLR pin during programming and debugging
operations.
Place the components shown in Figure 2-2 within
one-quarter inch (6 mm) from the MCLR pin.
FIGURE 2-2:
Note 1: R
example,
2: R1
Master Clear (MCLR) Pin
starting value is 10 k . Ensure that the
MCLR pin V
MCLR from the external capacitor C, in the
event of MCLR pin breakdown, due to
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS). Ensure that the MCLR pin
V
V
IH
DD
R
JP
and V
C
10 k
as
470
IL
shown
EXAMPLE OF MCLR PIN
CONNECTIONS
specifications are met.
IH
R1
is recommended. A suggested
will limit any current flowing into
© 2009 Microchip Technology Inc.
and V
IH
and V
IL
MCLR
in
specifications are met.
dsPIC33F
IL
Figure 2-2,
) and fast signal
it
is