AT90USB1287-MUR Atmel, AT90USB1287-MUR Datasheet - Page 179

• Manufacturer Part Number: AT90USB1287-MUR
• Description: MCU AVR 128K FLASH 16MHZ 64QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB1287-MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• Processor Series: AT90USBx
• Core: AVR8
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525, ATAVRQTOUCHX
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.1.5
17.2
7593K–AVR–11/09
Data Modes
SPI Data Register – SPDR
When a serial transfer is complete, the SPIF Flag is set. An interrupt is generated if SPIE in
SPCR is set and global interrupts are enabled. If SS is an input and is driven low when the SPI is
in Master mode, this will also set the SPIF Flag. SPIF is cleared by hardware when executing the
corresponding interrupt handling vector. Alternatively, the SPIF bit is cleared by first reading the
SPI Status Register with SPIF set, then accessing the SPI Data Register (SPDR).
• Bit 6 – WCOL: Write COLlision Flag
The WCOL bit is set if the SPI Data Register (SPDR) is written during a data transfer. The
WCOL bit (and the SPIF bit) are cleared by first reading the SPI Status Register with WCOL set,
and then accessing the SPI Data Register.
• Bit 5..1 – Res: Reserved Bits
These bits are reserved bits in the AT90USB64/128 and will always read as zero.
• Bit 0 – SPI2X: Double SPI Speed Bit
When this bit is written logic one the SPI speed (SCK Frequency) will be doubled when the SPI
is in Master mode (see
clock periods. When the SPI is configured as Slave, the SPI is only guaranteed to work at f
or lower.
The SPI interface on the AT90USB64/128 is also used for program memory and EEPROM
downloading or uploading. See
The SPI Data Register is a read/write register used for data transfer between the Register File
and the SPI Shift Register. Writing to the register initiates data transmission. Reading the regis-
ter causes the Shift Register Receive buffer to be read.
There are four combinations of SCK phase and polarity with respect to serial data, which are
determined by control bits CPHA and CPOL. The SPI data transfer formats are shown in
17-3
nal, ensuring sufficient time for data signals to stabilize. This is clearly seen by summarizing
Table 17-2
Bit
Read/Write
Initial Value
and
Figure
and
7
MSB
R/W
X
Table
17-4. Data bits are shifted out and latched in on opposite edges of the SCK sig-
6
R/W
X
17-3, as done below:
Table
5
R/W
X
17-4). This means that the minimum SCK period will be two CPU
page 380
4
R/W
X
for serial programming and verification.
3
X
R/W
2
R/W
X
1
R/W
X
AT90USB64/128
0
LSB
R/W
X
SPDR
Undefined
Figure
osc
179
/4