PIC16C73A-04/SP Microchip Technology, PIC16C73A-04/SP Datasheet - Page 119

• Manufacturer Part Number: PIC16C73A-04/SP
• Description: IC MCU OTP 4KX14 A/D PWM 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C73A-04/SP

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 22
• Ram Memory Size: 192Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

The ADRES register contains the result of the A/D con-
version. When the A/D conversion is complete, the
result is loaded into the ADRES register, the GO/DONE
bit (ADCON0<2>) is cleared, and A/D interrupt flag bit
ADIF is set. The block diagrams of the A/D module are
shown in Figure 13-3.
After the A/D module has been configured as desired,
the selected channel must be acquired before the con-
version is started. The analog input channels must
have their corresponding TRIS bits selected as an
input. To determine acquisition time, see Section 13.1.
After this acquisition time has elapsed the A/D conver-
sion can be started. The following steps should be fol-
lowed for doing an A/D conversion:
1.
2.
FIGURE 13-3: A/D BLOCK DIAGRAM
1997 Microchip Technology Inc.
Note 1: Not available on PIC16C72/73/73A/76.
Configure the A/D module:
• Configure analog pins / voltage reference /
• Select A/D input channel (ADCON0)
• Select A/D conversion clock (ADCON0)
• Turn on A/D module (ADCON0)
Configure A/D interrupt (if desired):
• Clear ADIF bit
• Set ADIE bit
• Set GIE bit
and digital I/O (ADCON1)
Converter
A/D
(Reference
voltage)
V
REF
(Input voltage)
PCFG2:PCFG0
V
IN
V
DD
001 or
011 or
101
000 or
010 or
100
3.
4.
5.
6.
7.
Wait the required acquisition time.
Start conversion:
• Set GO/DONE bit (ADCON0)
Wait for A/D conversion to complete, by either:
• Polling for the GO/DONE bit to be cleared
OR
• Waiting for the A/D interrupt
Read A/D Result register (ADRES), clear bit
ADIF if required.
For next conversion, go to step 1 or step 2 as
required. The A/D conversion time per bit is
defined as T
required before next acquisition starts.
CHS2:CHS0
111
110
101
100
011
010
001
000
AD
. A minimum wait of 2T
PIC16C7X
DS30390E-page 119
RA1/AN1
RE2/AN7
RA2/AN2
RA0/AN0
RE1/AN6
RE0/AN5
RA5/AN4
RA3/AN3/V
(1)
(1)
(1)
AD
REF
is