PIC16C73A-04/SP Microchip Technology, PIC16C73A-04/SP Datasheet - Page 36

• Manufacturer Part Number: PIC16C73A-04/SP
• Description: IC MCU OTP 4KX14 A/D PWM 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C73A-04/SP

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 22
• Ram Memory Size: 192Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16C7X
FIGURE 4-13: PIR1 REGISTER PIC16C73/73A/74/74A/76/77 (ADDRESS 0Ch)
DS30390E-page 36
bit7
bit 7:
bit 6:
bit 5:
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
Note 1: PIC16C73/73A/76 devices do not have a Parallel Slave Port implemented, this bit location is reserved
PSPIF
R/W-0
Interrupt flag bits get set when an interrupt condition occurs regardless of the state of its corresponding enable bit or the
global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to
enabling an interrupt.
(1)
PSPIF
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
RCIF: USART Receive Interrupt Flag bit
1 = The USART receive buffer is full (cleared by reading RCREG)
0 = The USART receive buffer is empty
TXIF: USART Transmit Interrupt Flag bit
1 = The USART transmit buffer is empty (cleared by writing to TXREG)
0 = The USART transmit buffer is full
SSPIF: Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: CCP1 Interrupt Flag bit
Capture Mode
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare Mode
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM Mode
Unused in this mode
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
on these devices, always maintain this bit clear.
R/W-0
ADIF
(1)
: Parallel Slave Port Read/Write Interrupt Flag bit
RCIF
R-0
TXIF
R-0
SSPIF
R/W-0
CCP1IF
R/W-0
TMR2IF
R/W-0
TMR1IF
R/W-0
bit0
R = Readable bit
W = Writable bit
U = Unimplemented bit,
- n = Value at POR reset
1997 Microchip Technology Inc.
read as ‘0’