PIC16C73A-04/SP Microchip Technology, PIC16C73A-04/SP Datasheet - Page 203

• Manufacturer Part Number: PIC16C73A-04/SP
• Description: IC MCU OTP 4KX14 A/D PWM 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C73A-04/SP

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Number Of I /o: 22
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 22
• Ram Memory Size: 192Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

19.2
DC CHARACTERISTICS
D001
D002*
D003
D004*
D005
D010
D010A
D015*
D020
D021
D021A
D023*
Note 1: This is the limit to which V
Param
1997 Microchip Technology Inc.
No.
*
†
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from charac-
6: The
DC Characteristics:
These parameters are characterized but not tested.
and are not tested.
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
MCLR = V
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
mated by the formula Ir = V
terization and is for design guidance only. This is not tested.
added to the base I
Supply Voltage
RAM Data Retention
Voltage (Note 1)
V
ensure internal Power-on
Reset signal
V
internal Power-on Reset
signal
Brown-out Reset Voltage B
Supply Current (Note 2,5) I
Brown-out Reset Current
(Note 6)
Power-down Current
(Note 3,5)
Brown-out Reset Current
(Note 6)
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
DD
DD
start voltage to
rise rate to ensure
Characteristic
current is the additional current consumed when this peripheral is enabled. This current should be
DD
; WDT enabled/disabled as specified.
DD
or I
PD
DD
DD
PIC16LC73A/74A-04 (Commercial, Industrial)
DD
V
V
V
S
I
DD
PD
Sym
I
I
DD
DR
POR
VDD
VDD
measurement.
can be lowered without losing RAM data.
BOR
BOR
measurements in active operation mode are:
/2Rext (mA) with Rext in kOhm.
Standard Operating Conditions (unless otherwise stated)
Operating temperature
0.05
Min
2.5
3.7
-
-
-
-
-
-
-
-
-
Typ† Max Units
22.5
V
350
350
1.5
4.0
2.0
7.5
0.9
0.9
SS
-
-
425
425
6.0
4.3
3.8
48
30
5
5
-
-
-
Applicable Devices 72 73 73A 74 74A 76 77
V/ms See section on Power-on Reset for details
mA
V
V
V
V
A
A
A
A
A
A
0˚C
-40˚C
XT, RC osc configuration
F
LP osc configuration
F
BOR enabled V
V
V
V
BOR enabled V
LP, XT, RC osc configuration (DC - 4 MHz)
See section on Power-on Reset for details
BODEN bit in configuration word enabled
OSC
OSC
DD
DD
DD
= 3.0V, WDT enabled, -40 C to +85 C
= 3.0V, WDT disabled, 0 C to +70 C
= 3.0V, WDT disabled, -40 C to +85 C
= 4 MHz, V
= 32 kHz, V
T
T
A
A
+85˚C for industrial and
+70˚C for commercial
DD
DD
DD
Conditions
DD
DD
PIC16C7X
= 5.0V
= 5.0V
= 3.0V (Note 4)
= 3.0V, WDT disabled
DS30390E-page 203
DD
and V
SS
.