ATXMEGA256A3B-AU Atmel, ATXMEGA256A3B-AU Datasheet - Page 97

• Manufacturer Part Number: ATXMEGA256A3B-AU
• Description: MCU AVR 256KB FLASH 64TQFP
• Manufacturer: Atmel
• Series: AVR® XMEGAr

Specifications of ATXMEGA256A3B-AU

• Core Processor: AVR
• Core Size: 8/16-Bit
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 49
• Program Memory Size: 256KB (128K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.6 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Controller Family/series: ATXMEGA
• No. Of I/o's: 49
• Eeprom Memory Size: 4KB
• Ram Memory Size: 16KB
• Cpu Speed: 32MHz
• Rohs Compliant: Yes
• Processor Series: XMEGA
• Core: AVR
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 16 KB
• Interface Type: SPI, TWI, USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 49
• Number Of Timers: 7
• Operating Supply Voltage: 2.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8116I–AVR–09/10
7. Configuration of PGM and CWCM not as described in XMEGA A Manual
Table 36-1.
8. PWM is not restarted properly after a fault in cycle-by-cycle mode
9. BOD will be enabled after any reset
10. DAC is nonlinear and inaccurate when reference is above 2.4V or VCC - 0.6V
11.
Problem fix/Workaround
None.
Enabling Common Waveform Channel Mode will enable Pattern generation mode (PGM),
but not Common Waveform Channel Mode.
Enabling Pattern Generation Mode (PGM) and not Common Waveform Channel Mode
(CWCM) will enable both Pattern Generation Mode and Common Waveform Channel Mode.
Problem fix/Workaround
When the AWeX fault restore mode is set to cycle-by-cycle, the waveform output will not
return to normal operation at first update after fault condition is no longer present.
Problem fix/Workaround
Do a write to any AWeX I/O register to re-enable the output.
If any reset source goes active, the BOD will be enabled and keep the device in reset if the
VCC voltage is below the programmed BOD level. During Power-On Reset, reset will not be
released until VCC is above the programmed BOD level even if the BOD is disabled.
Problem fix/Workaround
Do not set the BOD level higher than VCC even if the BOD is not used.
Using the DAC with a reference voltage above 2.4V or VCC - 0.6V will give inaccurate out-
put when converting codes that give below 0.75V output:
– ±10 LSB for continuous mode
– ±200 LSB for Sample and Hold mode
Problem fix/Workaround
None.
DAC has increased INL or noise for some operating conditions
Some DAC configurations or operating condition will result in increased output error.
– Continous mode: ±5 LSB
– Sample and hold mode: ±15 LSB
– Sample and hold mode for reference above 2.0v: up to ±100 LSB
Problem fix/Workaround
None.
PGM
0
0
1
1
Configure PWM and CWCM according to this table:
CWCM
0
1
0
1
Description
PGM and CWCM disabled
PGM enabled
PGM and CWCM enabled
PGM enabled
XMEGA A3B
97