DS87C530-QNL Maxim Integrated Products, DS87C530-QNL Datasheet - Page 13

• Manufacturer Part Number: DS87C530-QNL
• Description: IC MCU EPR/ROM W/RTC 33MZ 52PLCC
• Manufacturer: Maxim Integrated Products
• Series: 87Cr

Specifications of DS87C530-QNL

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SIO, UART/USART
• Peripherals: Power-Fail Reset, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: OTP
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-LCC, 52-PLCC
• Processor Series: DS87C530
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: UART
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -
• Other names: DS87C530QNL

space SRAM is read/write accessible and is memory mapped. This on-chip SRAM is reached by the
MOVX instruction. It is not used for executable memory. The scratchpad area is 256 bytes of register
mapped RAM and is identical to the RAM found on the 80C52. There is no conflict or overlap among the
256 bytes and the 1kB as they use different addressing modes and separate instructions.
OPERATIONAL CONSIDERATION
The erasure window of the windowed LCC should be covered without regard to the
programmed/unprogrammed state of the EPROM. Otherwise, the device may not meet the AC and DC
parameters listed in the data sheet.
PROGRAM MEMORY ACCESS
On-chip ROM begins at address 0000h and is contiguous through 3FFFh (16kB). Exceeding the
maximum address of on-chip ROM will cause the DS87C530/DS83C530 to access off-chip memory.
However, the maximum on-chip decoded address is selectable by software using the ROMSIZE feature.
Software can cause the microcontroller to behave like a device with less on-chip memory. This is
beneficial when overlapping external memory, such as Flash, is used.
The maximum memory size is dynamically variable. Thus a portion of memory can be removed from the
memory map to access off-chip memory, then restored to access on-chip memory. In fact, all the on-chip
memory can be removed from the memory map allowing the full 64kB memory space to be addressed
from off-chip memory. ROM addresses that are larger than the selected maximum are automatically
fetched from outside the part via Ports 0 and 2. Figure 4 shows a depiction of the ROM memory map.
The ROMSIZE register is used to select the maximum on-chip decoded address for ROM. Bits RMS2,
RMS1, RMS0 have the following effect:
The reset default condition is a maximum on-chip ROM address of 16kB. Thus no action is required if
this feature is not used. When accessing external program memory, the first 16kB would be inaccessible.
To select a smaller effective ROM size, software must alter bits RMS2–RMS0. Altering these bits
requires a timed-access procedure.
Care should be taken so that changing the ROMSIZE register does not corrupt program execution. For
example, assume that a device is executing instructions from internal program memory near the 12kB
boundary (~3000h) and that the ROMSIZE register is currently configured for a 16kB internal program
space. If software reconfigures the ROMSIZE register to 4kB (0000h–0FFFh) in the current state, the
RMS2
0
0
0
0
1
1
1
1
RMS1
0
0
1
1
0
0
1
1
DS87C530/DS83C530 EPROM/ROM Microcontrollers with Real-Time Clock
RMS0
0
1
0
1
0
1
0
1
13 of 45
MAXIMUM ON-CHIP ROM ADDRESS
Invalid—reserved
Invalid—reserved
16kB (default)
0kB
1kB
2kB
4kB
8kB