LM12CLK/NOPB National Semiconductor, LM12CLK/NOPB Datasheet
LM12CLK/NOPB
Specifications of LM12CLK/NOPB
*LM12CLK/NOPB
LM12
LM12CLK
Related parts for LM12CLK/NOPB
LM12CLK/NOPB Summary of contents
Page 1
... Part number 8112-AG7 Bottom View Order Number LM12CLK See NS Package Number K04A © 2008 National Semiconductor Corporation 8704 Version 7 Revision 4 This monolithic op amp is compensated for unity-gain feed- back, with a small-signal bandwidth of 700 kHz. Slew rate is 9V/μs, even as a follower. Distortion and capacitive-load sta- bility rival that of the best designs using complementary out- put transistors ...
Page 2
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Total Supply Voltage (Note 1) Input Voltage Output Current Junction Temperature Electrical Characteristics Parameter Input Offset Voltage ±10V Input Bias Current V− Input Offset Current V− ...
Page 3
Although the output and supply leads are resistant to electrostatic discharges from handling, the input leads are not. The part should be treated accordingly. Output-Transistor Ratings (guaranteed) Safe Area Pulse Thermal Resistance Typical Performance Characteristics Pulse Power Limit 8704 Version ...
Page 4
Peak Output Current Large Signal Response Large Signal Gain www.national.com 870436 870438 870440 4 8704 Version 7 Revision 4 Print Date/Time: 2008/09/16 12:48:40 Output Saturation Voltage 870437 Follower Pulse Response 870439 Thermal Response 870441 ...
Page 5
Total Harmonic Distortion 870442 Output Impedance 870444 Input Bias Current 870446 8704 Version 7 Revision 4 Frequency Response Power Supply Rejection Input Noise Voltage 5 Print Date/Time: 2008/09/16 12:48:40 870443 870445 870447 www.national.com ...
Page 6
Common Mode Rejection Supply Current Application Information GENERAL Twenty five years ago the operational amplifier was a spe- cialized design tool used primarily for analog computation. However, the availability of low cost IC op amps in the late 1960's prompted ...
Page 7
The current in the supply leads is a rectified component of the load current. If adequate bypassing is not provided, this dis- torted signal can be fed back into internal circuitry. Low dis- tortion at high frequencies requires that the ...
Page 8
The LM12 can be made stable for all loads with a large ca- pacitor on the output, as shown above. This compensation gives the lowest possible closed-loop output impedance at high frequencies and the best load-transient response appropriate ...
Page 9
This connection allows increased output capability without requiring a separate control amplifier. The output buffer, A provides load current through R equal to that supplied by the 5 main amplifier through R . Again, more output buffers can ...
Page 10
Discrete transistors can be used to increase output drive to ±70V at ±10A as shown above. With proper thermal design, OPERATIONAL POWER SUPPLY Note: Supply voltages for the LM318s are ±15V External current limit can be provided for a power ...
Page 11
This motor/tachometer servo gives an output speed propor- tional to input voltage. A low-level op amp is used for fre- quency shaping while the power op amp provides current drive to the motor. Current drive eliminates loop phase shift due ...
Page 12
AUDIO AMPLIFIERS A power amplifier suitable for use in high-quality audio equip- ment is shown above. Harmonic distortion is about 0.01- percent. Intermodulation distortion (60 Hz/7 kHz, 4:1) mea- sured 0.015-percent. Transient response and saturation recovery are clean, and the ...
Page 13
VOLTAGE REGULATOR DISSIPATION The pass transistor dissipation of a voltage regulator is easily determined in the operating mode. Maximum continuous dis- sipation occurs with high line voltage and maximum load current. As discussed earlier, ripple voltage can be averaged if ...
Page 14
Input offset current: The absolute value of the difference in the two input currents with the output voltage and current at zero. Common-mode rejection: The ratio of the input voltage range to the change in offset voltage between the extremes. ...
Page 15
Physical Dimensions inches (millimeters) unless otherwise noted 8704 Version 7 Revision 4 4-Lead TO-3 Steel Package (K) Order Number LM12CLK NS Package Number K04A 15 Print Date/Time: 2008/09/16 12:48:40 www.national.com ...
Page 16
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock Conditioners www.national.com/timing Data Converters www.national.com/adc Displays www.national.com/displays Ethernet www.national.com/ethernet Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www ...