MC33204DG ON Semiconductor, MC33204DG Datasheet - Page 9

• Manufacturer Part Number: MC33204DG
• Description: IC OPAMP QUAD R-R LV 14-SOIC
• Manufacturer: ON Semiconductor

Specifications of MC33204DG

• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Output Type: Rail-to-Rail
• Slew Rate: 1 V/µs
• Gain Bandwidth Product: 2.2MHz
• Current - Input Bias: 80nA
• Voltage - Input Offset: 10000µV
• Current - Supply: 1.125mA
• Current - Output / Channel: 80mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 12 V, ±0.9 V ~ 6 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Channels: 4
• Common Mode Rejection Ratio (min): 60 dB
• Input Voltage Range (max): Positive Rail
• Input Voltage Range (min): Negative Rail
• Input Offset Voltage: 10 mV
• Input Bias Current (max): 200 nA
• Operating Supply Voltage: 12 V
• Supply Current: 3.6 mA
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Dual Supply Voltage: +/- 3 V, +/- 5 V
• Maximum Dual Supply Voltage: +/- 6 V
• Minimum Dual Supply Voltage: +/- 0.9 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 12 V
• Supply Voltage (min): 1.8 V
• Technology: Bipolar
• Voltage Gain Db: 109.54 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MC33204DG; MC33204DGOS

unique in their ability to swing rail−to−rail on both the input
and the output with a completely bipolar design. This offers
low noise, high output current capability and a wide
common mode input voltage range even with low supply
voltages. Operation is guaranteed over an extended
temperature range and at supply voltages of 2.0 V, 3.3 V and
5.0 V and ground.
V
voltage supplies. The MC33201/2/4 are guaranteed not to
latch or phase reverse over the entire common mode range,
however, the inputs should not be allowed to exceed
maximum ratings.
design. The footprint for the semiconductor packages must be
the correct size to ensure proper solder connection interface
CC
The MC33201/2/4 family of operational amplifiers are
Since the common mode input voltage range extends from
Surface mount board layout is a critical portion of the total
to V
V
V
R
C
T
A
Figure 26. Noninverting Amplifier Slew Rate
CC
EE
L
L
= 25°C
= 600 W
= 100 pF
EE
= - 6.0 V
= + 6.0 V
, it can be operated with either single or split
General Information
t, TIME (5.0 ms/DIV)
DETAILED OPERATING DESCRIPTION
Figure 28. Large Signal Transient Response
V
V
R
C
A
T
A
CC
EE
V
L
L
= 25°C
= 600 W
= 100 pF
= 1.0
= - 6.0 V
= + 6.0 V
http://onsemi.com
t, TIME (10 ms/DIV)
9
amplifiers by using parallel NPN−PNP differential input
stages. When the inputs are within 800 mV of the negative
rail, the PNP stage is on. When the inputs are more than 800
mV greater than V
input pairs will cause a reversal of input bias currents (see
Figure 6). Also, slight differences in offset voltage may be
noted between the NPN and PNP pairs. Cross−coupling
techniques have been used to keep this change to a minimum.
is current boosted to provide 80 mA of output current,
enabling the op amp to drive 600 W loads. Because of this
high output current capability, care should be taken not to
exceed the 150°C maximum junction temperature.
between the board and the package. With the correct pad
geometry, the packages will self−align when subjected to a
solder reflow process.
Rail−to−rail performance is achieved at the input of the
In addition to its rail−to−rail performance, the output stage
Figure 27. Small Signal Transient Response
EE
Circuit Information
, the NPN stage is on. This switching of
t, TIME (10 ms/DIV)
V
V
R
C
T
A
CC
EE
L
L
= 600 W
= 100 pF
= 25°C
= - 6.0 V
= + 6.0 V