XBP09-XC009-DK Digi International, XBP09-XC009-DK Datasheet - Page 7

• Manufacturer Part Number: XBP09-XC009-DK
• Description: KIT STARTER XBEE PRO 900MHZ
• Manufacturer: Digi International
• Series: XBEE-PRO™r
• Type: Transceiver, XBeePror

Specifications of XBP09-XC009-DK

• Frequency: 900MHz
• Wireless Frequency: 900 MHz
• Operating Voltage: 3.3 V
• Output Power: 100 mW
• Antenna: U.FL, RPSMA, Whip
• Operating Temperature Range: - 40 C to + 85 C
• For Use With/related Products: Xbee-PRO Modules
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 602-1133; Q4227731; XBP09-XC009-DK

XBee‐PRO® XSC OEM RF Modules
1.3. Pin Signals
Figure 1‐01. XBee‐PRO XSC OEM RF Module Pin Numbers (top view, shield underneath)
Table 1‐02. J1 Pin Signal Descriptions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
© 2008 Digi International, Inc.
Module Pin
(Low‐asserted signals distinguished with a horizontal line over signal name.)
VCC
DO (Data Out)
DI (Data In
DO3 / RX LED
DI3 / SLEEP
GND
DO2 / CTS / RS-485
Enable
ON / Sleep
VREF
DI2 / RTS / CMD
Reset
Config
TX / PWR
Public Signal
Notes
Has a
10k pull
up
resistor
Has a
100k
pull up
resistor
Has a
100k
pull up
resistor
Has a
100k
pull
down
resistor
O
I
O
I
I/O
I
O
NC
I
O
O
O
I
O
I
O
O
I/O
n/a
n/a
high
low
low / high
Driven high
high
Driven high
low
high
n/a
n/a
low
Driven low
Driven low
Active
When
3.0VDC to 3.6VDC
Serial data exiting the module (to the UART host).
Refer to the Serial Communications section for more
information
Serial data entering the module (from UART host).
Refer to the Serial Communications section for more
information.
Pin is driven high during RF data reception; otherwise,
the pin is driven low. Refer to the CD Command
section to enable.
Re-boot module.(minimum pulse is 90us) Open Drain
configuration. Module will drive reset line low
momentarily on reboot and power up.
Pin can be used as a backup method for entering
Command Mode during power-up. Primary method is
with "+++". Refer to the AT Commands section for
more information.
Do not Connect
Do not Connect
By default, DI3 pin is not used. To configure this pin to
support Sleep Modes, refer to the Sleep Mode, SM
Command and PW Command sections.
Ground
Do not Connect
CTS(clear-to-send) flow control - When pin is driven
low, UART host is permitted to send serial data to the
module. Refer to the Serial Communications and CS
Command sections for more information.
RS-485 Enable - To configure this pin to enable RS-
485 (2-wire or 4-wire) communications, refer to the
Serial Communications and CS Command sections.
high = Indicates power is on and module is not in
Sleep Mode. Low = Sleep mode or module is
unpowered
Not used on this module. For compatibility with other
XBee modules, we recommend connecting this pin to
a voltage reference if Analog sampling is desired.
Otherwise, connect to GND.
low = TX - Pin pulses low during transmission
--------------------------------------------------------------
high = PWR - Indicates power is on and module is not
in Sleep Mode
pin is not used. To configure this pin to regulate the
flow of serial data exiting the module, refer to the
Serial Communications and RT Command sections.
---------------------------------------------------------------
CMD -Refer to Binary Commands and RT
Commandsections to enable binary command
programming.
Do not Connect
Do not Connect
----------------------------------------------------------------
RTS (request-to-send) flow control - By default, this
Function
7