XBP24-ACI-001 Digi International/Maxstream, XBP24-ACI-001 Datasheet - Page 31

• Manufacturer Part Number: XBP24-ACI-001
• Description: MODULE 802.15.4 100MW CHIP ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-ACI-001

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 20dBm (100mW)
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 215mA @ 3.3V
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -

RF Interfacing
Table 3‐03. XBee/XBee‐PRO Commands ‐ RF Interfacing
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Sleep (Low Power)
Table 3‐04. XBee®/XBee‐PRO® Commands ‐ Sleep (Low Power)
XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
AT
Command
PL
CA (v1.x80*)
AT
Command
SM
SO
ST
SP
DP (1.x80*)
Command
Category
Sleep
(Low Power)
Sleep (Low
Power)
Sleep
(Low Power)
Sleep
(Low Power)
Sleep
(Low Power)
Command
Category
RF Interfacing
RF Interfacing
Name and Description
Sleep Mode. Set/Read Sleep Mode configurations.
Sleep Options Set/Read the sleep mode options.
Bit 0 - Poll wakeup disable
0 - Normal operations. A module configured for cyclic sleep will poll for data on waking.
1 - Disable wakeup poll. A module configured for cyclic sleep will not poll for data on
waking.
Bit 1 - ADC/DIO wakeup sampling disable.
0 - Normal operations. A module configured in a sleep mode with ADC/DIO sampling
enabled will automatically perform a sampling on wakeup.
1 - Suppress sample on wakeup. A module configured in a sleep mode with ADC/DIO
sampling enabled will not automatically sample on wakeup.
Time before Sleep. <NonBeacon firmware> Set/Read time period of inactivity (no
serial or RF data is sent or received) before activating Sleep Mode. ST parameter is
only valid with Cyclic Sleep settings (SM = 4 - 5).
Coordinator and End Device ST values must be equal.
Also note, the GT parameter value must always be less than the ST value. (If GT > ST,
the configuration will render the module unable to enter into command mode.) If the ST
parameter is modified, also modify the GT parameter accordingly.
Cyclic Sleep Period. <NonBeacon firmware> Set/Read sleep period for cyclic sleeping
remotes. Coordinator and End Device SP values should always be equal. To send
Direct Messages, set SP = 0.
End Device - SP determines the sleep period for cyclic sleeping remotes. Maximum
sleep period is 268 seconds (0x68B0).
Coordinator - If non-zero, SP determines the time to hold an indirect message before
discarding it. A Coordinator will discard indirect messages after a period of (2.5 * SP).
Disassociated Cyclic Sleep Period. <NonBeacon firmware>
End Device - Set/Read time period of sleep for cyclic sleeping remotes that are
configured for Association but are not associated to a Coordinator. (i.e. If a device is
configured to associate, configured as a Cyclic Sleep remote, but does not find a
Coordinator, it will sleep for DP time before reattempting association.) Maximum sleep
period is 268 seconds (0x68B0). DP should be > 0 for NonBeacon systems.
Name and Description
Power Level. Select/Read the power level at which the RF module transmits conducted
power.
CCA Threshold. Set/read the CCA (Clear Channel Assessment) threshold. Prior to
transmitting a packet, a CCA is performed to detect energy on the channel. If the
detected energy is above the CCA Threshold, the module will not transmit the packet.
© 2009 Digi Internatonal, Inc.
Parameter Range
0 - 5
0-4
1 - 0xFFFF [x 1 ms]
0 - 0x68B0 [x 10 ms]
1 - 0x68B0 [x 10 ms]
Parameter Range
0 - 4 (XBee / XBee-PRO)
XBee-PRO International
variant:
PL=4: 10 dBm
PL=3: 8 dBm
PL=2: 2 dBm
PL=1: -3 dBm
PL=0: -3 dBm
0x24 - 0x50 [-dBm]
0 = No Sleep
1 = Pin Hibernate
2 = Pin Doze
3 = Reserved
4 = Cyclic sleep remote
5 = Cyclic sleep remote
6 = [Sleep Coordinator] for
0 = -10 / 10 dBm
1 = -6 / 12 dBm
2 = -4 / 14 dBm
3 = -2 / 16 dBm
4 = 0 / 18 dBm
backwards compatibility
w/ v1.x6 only; otherwise,
use CE command.
w/ pin wake-up
Default
0
0
0x1388
(5000d)
0x3E8
(1000d)
Default
4
0x2C
(-44d dBm)
0
31