XBP24-ACI-001 Digi International/Maxstream, XBP24-ACI-001 Datasheet - Page 50

• Manufacturer Part Number: XBP24-ACI-001
• Description: MODULE 802.15.4 100MW CHIP ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-ACI-001

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 20dBm (100mW)
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 215mA @ 3.3V
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -

XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
NT (Node Discover Time) Command
P0 (PWM0 Configuration) Command
P1 (PWM1 Configuration) Command
PL (Power Level) Command
<Networking {Identification}> The NT command
is used to set the amount of time a base node will
wait for responses from other nodes when using
the ND (Node Discover) command. The NT value
is transmitted with the ND command.
Remote nodes will set up a random hold-off time
based on this time. The remotes will adjust this
time down by 250 ms to give each node the abil-
ity to respond before the base ends the command. Once the ND command has ended, any
response received on the base will be discarded.
<I/O Setting {I/O Line Passing}> The P0 com-
mand is used to select/read the function for
PWM0 (Pulse Width Modulation output 0). This
command enables the option of translating
incoming data to a PWM so that the output can be
translated back into analog form.
With the IA (I/O Input Address) parameter cor-
rectly set, AD0 values can automatically be
passed to PWM0.
<I/O Setting {I/O Line Passing}> The P1 com-
mand is used to select/read the function for
PWM1 (Pulse Width Modulation output 1). This
command enables the option of translating
incoming data to a PWM so that the output can be
translated back into analog form.
With the IA (I/O Input Address) parameter cor-
rectly set, AD1 values can automatically be
passed to PWM1.
<RF Interfacing> The PL com-
mand is used to select and read
the power level at which the RF
module transmits conducted
power.
When operating in Europe,
XBee-PRO 802.15.4 modules
must operate at or below a
transmit power output level of
10dBm. Customers have 2
choices for transmitting at or
below 10dBm:
© 2009 Digi Internatonal, Inc.
• Order the standard XBee-
• Order the International variant of the XBee-PRO module, which has a maximum transmit out-
PRO module and change
the PL command to "0"
(10dBm),
put power of 10dBm.
AT Command: ATPL
Parameter Range: 0 - 4
Default Parameter Value: 4
Parameter
0
1
2
3
4
AT Command: ATNT
Parameter Range: 0x01 - 0xFC
Default: 0x19 (2.5 decimal seconds)
Related Commands: ND (Node Discover)
Minimum Firmware Version Required: 1.xA0
AT Command: ATP0
The second character in the command is the
number zero (“0”), not the letter “O”.
Parameter Range: 0 - 2
AT Command: ATP1
Parameter Range: 0 - 2
Default Parameter Value: 0
Minimum Firmware Version Required: v1.xA0
Default Parameter Value: 1
-10 dBm
-6 dBm
-4 dBm
-2 dBm
0 dBm
XBee
Parameter
Parameter
0
1
2
0
1
2
[x 100 msec]
XBee-PRO
10 dBm
12 dBm
14 dBm
16 dBm
18 dBm
Configuration
Configuration
PWM0 Output
PWM1 Output
Disabled
Disabled
PL=4: 10 dBm
PL=1: -3 dBm
PL=0: -3 dBm
International
PL=3: 8 dBm
PL=2: 2 dBm
RSSI
RSSI
XBee-PRO
variant
50