X24-009NSC Digi International/Maxstream, X24-009NSC Datasheet - Page 6

• Manufacturer Part Number: X24-009NSC
• Description: MOD RF 2.4GHZ 9600BPS W/RPSMA
• Manufacturer: Digi International/Maxstream

Specifications of X24-009NSC

• Frequency: 2.4GHz
• Data Rate - Maximum: 19.2kbps
• Modulation Or Protocol: FSK
• Power - Output: 17dBm
• Sensitivity: -110dBm
• Voltage - Supply: 5V
• Current - Receiving: 80mA
• Current - Transmitting: 150mA
• Data Interface: PCB, Through Hole
• Antenna Connector: RP-SMA
• Operating Temperature: 0°C ~ 70°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -

XStream™ OEM RF Module – Product Manual v5.x00 [2006.02.24]
1.4. Pin Signals
Figure 1‐02. XStream OEM RF Module Pin Numbers (bottom view, pins protruding)
Table 1‐02. J1 Pin Signal Descriptions
(Low‐asserted signals distinguished with a horizontal line over signal name.)
*
**
***
Note: When integrating the XStream Module with a Host PC Board, all lines that are not used should
be left disconnected (floating).
Table 1‐03. J2 Pin Signal Descriptions
J2 Pins are used primarily for mechanical stability and may be left disconnected.
© 2006 MaxStream, Inc. Confidential and Proprietary
Module Pin
Module Pin
10
11
1
2
3
4
5
6
7
8
9
1
2
3
4
Module has 10K Ω internal pull‐up resistor
Module has 10K Ω internal pull‐down resistor
Module has 100K Ω internal pull‐up resistor
DI2 /
Signal Name
RS-485 Enable
Signal Name
DO3 / RX LED
DO (data out)
DI3 / SLEEP
DO2 /
DI (data in)
reserved
GND
VCC
GND
GND
GND
/ PWR
/ CMD
/
I/O
I***
O*
O*
I**
O
O
I*
I*
-
I
I
When Active
high
high
high
low
n/a
n/a
low
low
low
low
-
-
Function
UART host is permitted to send serial data to the module.
Refer to the Serial Communications [p9] and CS Command
[p23] sections for more information.
RS-485 Enable – To configure this pin to enable RS-485
(2-wire or 4--wire) communications, refer to the Serial
Communications [p9] and CS Command [p23] sections.
By default, DI3 pin is not used. To configure this pin to support
Sleep Modes, refer to the Sleep Mode [p13], SM Command
[p32] and PW Command [p29] sections.
Serial data exiting the module (to the UART host). Refer to the
Serial Communications [p9] section for more information.
Serial data entering the module (from UART host). Refer to the
Serial Communications [p9] section for more information.
used. To configure this pin to regulate the flow of serial data
exiting the module, refer to the Serial Communications [p9] and
RT Command [p31] sections.
CMD –Refer to Binary Commands [p17] and RT Command
[p31] sections to enable binary command programming.
Re-boot module.
Pin is driven high during RF data reception; otherwise, the pin
is driven low. Refer to the CD Command [p22] to enable.
PWR – Indicates power is on and module is not in Sleep Mode.
Pin can be used as a backup method for entering Command
Mode during power-up. Primary method is with “+++”. Refer to
the Command Mode [p16] section for more information.
5 VDC regulated (± 0.25)
Ground
- Pin pulses low during RF transmission.
(clear-to-send) flow control – When pin is driven low,
(request-to-send) flow control – By default, this pin is not
6