X09-019WNC Digi International/Maxstream, X09-019WNC Datasheet - Page 39

• Manufacturer Part Number: X09-019WNC
• Description: MOD RF 900MHZ 19.2K W/WIRE ANT
• Manufacturer: Digi International/Maxstream
• Series: XStream™r

Specifications of X09-019WNC

• Frequency: 900MHz
• Data Rate - Maximum: 19.2kbps
• Modulation Or Protocol: FSK
• Power - Output: 100mW
• Sensitivity: -110dBm
• Voltage - Supply: 5V
• Current - Receiving: 50mA
• Current - Transmitting: 140mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Antenna
• Operating Temperature: 0°C ~ 70°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Applications: -
• Memory Size: -

XStream™ OEM RF Module – Product Manual v5.x00 [2006.02.24]
Repeater Network Configuration
Configuration Instruction (Basic Broadcast Communications)
A network may consist of End Nodes (EN), End/Repeater Nodes (ERN) and a Base Node (BN).
The base node initiates all communications.
The repeater network can be configured to operate using Basic Broadcast or Basic Addressed
communications. The addressing capabilities of the modules allow integrators to send a packet as
a global packet (DT = 0xFFFF) and shift out of every radio in the network (Basic Broadcast).
Alternatively, the packet can be sent with a specific DT (Destination Address) parameter so that it
is only accepted by a specific remote node (Basic Addressed).
Assign each module a unique MY (source) address. (The AM (Auto-set MY) command will
configure a unique source address that is based on module serial number.)
Enable Basic Broadcast Communications (DT = 0xFFFF) or Addressed Broadcast Communications
(ATDT specifies a specific destination)
Configure PK, RO and RB to ensure that RF packet aligns with protocol packet. (ex. PK=0x100,
RB=0x100, RO depends on baud rate).
Configure one or more repeaters in the system (ATMD = 3).
Configure remote nodes as destinations (MD = 4). This will ensure that the remote node waits for
the repeater traffic to subside before it transmits a response.
The configuration instructions above reflect configuration for a Basic Broadcast Repeater system.
To configure a Basic Addressed Repeater system, use the DT (Destination Address) parameter to
assign unique addresses to each module in the network.
Algorithm details
Packets may be shifted out the serial port and/or repeated depending on the DT parameter
contained in the RF packet.
Table 4‐02. DT (Destination Address) parameter truth table
Address Match
Global
Local
None
Repeat delay based on RSSI
A transmitted packet may be received by more that one repeater at the same time. In order to
reduce the probability that the repeaters will transmit at the same instant, resulting in a collision
and possible data loss; an algorithm has been developed that will allow a variable back-off prior
to retransmission of the packet by a repeater. The algorithm allows radios that receive the packet
with a stronger RF signal (RSSI) to have the first opportunity to retransmit the packet.
The RN (Delay Slots) parameter is used to configure this delay. Set RN=0 (no delays) for small
networks with few repeaters or repeaters that are not within range of each other. Set RN=1 for
systems with 2 to 5 repeaters that may be within range of each other.
The actual length of the delay is computed by the formula:
Where L is the length of the transmitted packet in milliseconds, DS is the number of delay slots
to wait, RSSI is the received signal strength in dBm, RN is the value of the RN register and
RandomInt(A,B) is a function that returns a random integer from A to B-0
© 2006 MaxStream, Inc. Confidential and Proprietary
• Packet ID (PID) is composed of transmitting module MY address and packet serial number.
• Incoming packets with a PID already found in the PID buffer will be ignored.
• Each module maintains a PID buffer 8 deep of previously received packets (managed as
Delay (ms) = L * DS
DS = (-41-RSSI)/10*RN)+RandomInt(0,RN)
FIFO).
Send out serial port?
Yes
Yes
No
Repeat?
Yes
No
Yes
39