PIC18LF24K22-I/SS Microchip Technology, PIC18LF24K22-I/SS Datasheet - Page 201

• Manufacturer Part Number: PIC18LF24K22-I/SS
• Description: IC PIC MCU 16KB FLASH 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18LF24K22-I/SS

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 19x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP (0.200", 5.30mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 768Byte
• Cpu Speed: 64MHz
• No. Of Timers: 7
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TABLE 14-14: CONFIGURATION REGISTERS ASSOCIATED WITH CAPTURE
REGISTER 14-1:
 2010 Microchip Technology Inc.
CONFIG3H
Legend: — = Unimplemented location, read as ‘0’. Shaded bits are not used by Capture mode.
bit 7
Legend:
R = Readable bit
u = Bit is unchanged
‘1’ = Bit is set
bit 7-6
bit 5-4
bit 3-0
Note 1:
Name
U-0
—
This feature is available on CCP5 only.
MCLRE
Bit 7
Unused
DCxB<1:0>: PWM Duty Cycle Least Significant bits
Capture mode:
Unused
Compare mode:
Unused
PWM mode:
These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPRxL.
CCPxM<3:0>: ECCPx Mode Select bits
0000 = Capture/Compare/PWM off (resets the module)
0001 = Reserved
0010 = Compare mode: toggle output on match
0011 = Reserved
0100 = Capture mode: every falling edge
0101 = Capture mode: every rising edge
0110 = Capture mode: every 4th rising edge
0111 = Capture mode: every 16th rising edge
1000 = Compare mode: set output on compare match (CCPx pin is set, CCPxIF is set)
1001 = Compare mode: clear output on compare match (CCPx pin is cleared, CCPxIF is set)
1010 = Compare mode: generate software interrupt on compare match (CCPx pin is unaffected,
1011 = Compare mode: Special Event Trigger (CCPx pin is unaffected, CCPxIF is set)
11xx =: PWM mode
U-0
—
CCPxCON: STANDARD CCPx CONTROL REGISTER
CCPxIF is set)
Bit 6
—
W = Writable bit
x = Bit is unknown
‘0’ = Bit is cleared
R/W-0
P2BMX
Bit 5
DCxB<1:0>
TimerX (selected by CxTSEL bits) is reset
ADON is set, starting A/D conversion if A/D module is enabled
T3CMX
R/W-0
Bit 4
Preliminary
HFOFST
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Reset
Bit 3
R/W-0
PIC18(L)F2X/4XK22
CCP3MX
Bit 2
R/W-0
CCPxM<3:0>
PBADEN
Bit 1
R/W-0
CCP2MX
DS41412D-page 201
Bit 0
(1)
R/W-0
Register
on Page
354
bit 0